SIMCOM社の SIM7090G を使ったSpresense用のAddon Board を作ってみた

以前 SIMCOM 社の SIM7080G を使ったSpresense用のAddon Board の記事を書きましたが
今回 SIM7080G と同スペックの SIM7090G を使った Addon Board を作ってみました。
SIM7080Gを使ったときの記事

写真を見ていただくと分かりますがSIM7090きが一回り小さいので
Spresense のビン間に収まり、センサー搭載用のスペースも確保できました。

テストに使ったプログラムは SIM7080G の時と同じ
TinyGSM のサンプルプログラム HttpClient.ino です。

SIM7090G_Spresense.ino

/**************************************************************
 *
 * This sketch connects to a website and downloads a page.
 * It can be used to perform HTTP/RESTful API calls.
 *
 * For this example, you need to install ArduinoHttpClient library:
 *   https://github.com/arduino-libraries/ArduinoHttpClient
 *   or from http://librarymanager/all#ArduinoHttpClient
 *
 * TinyGSM Getting Started guide:
 *   https://tiny.cc/tinygsm-readme
 *
 * For more HTTP API examples, see ArduinoHttpClient library
 *
 * NOTE: This example may NOT work with the XBee because the
 * HttpClient library does not empty to serial buffer fast enough
 * and the buffer overflow causes the HttpClient library to stall.
 * Boards with faster processors may work, 8MHz boards will not.
 **************************************************************/

// Select your modem:
// #define TINY_GSM_MODEM_SIM800
// #define TINY_GSM_MODEM_SIM808
// #define TINY_GSM_MODEM_SIM868
// #define TINY_GSM_MODEM_SIM900
// #define TINY_GSM_MODEM_SIM7000
// #define TINY_GSM_MODEM_SIM7000SSL
#define TINY_GSM_MODEM_SIM7080
// #define TINY_GSM_MODEM_SIM5360
// #define TINY_GSM_MODEM_SIM7600
// #define TINY_GSM_MODEM_UBLOX
// #define TINY_GSM_MODEM_SARAR4
// #define TINY_GSM_MODEM_M95
// #define TINY_GSM_MODEM_BG96
// #define TINY_GSM_MODEM_A6
// #define TINY_GSM_MODEM_A7
// #define TINY_GSM_MODEM_M590
// #define TINY_GSM_MODEM_MC60
// #define TINY_GSM_MODEM_MC60E
// #define TINY_GSM_MODEM_ESP8266
// #define TINY_GSM_MODEM_XBEE
// #define TINY_GSM_MODEM_SEQUANS_MONARCH

// Set serial for debug console (to the Serial Monitor, default speed 115200)
#define SerialMon Serial

// Set serial for AT commands (to the module)
// Use Hardware Serial on Mega, Leonardo, Micro
#ifndef __AVR_ATmega328P__
#define SerialAT Serial2

// or Software Serial on Uno, Nano
#else
#include <SoftwareSerial.h>
SoftwareSerial SerialAT(2, 3);  // RX, TX
#endif

// Increase RX buffer to capture the entire response
// Chips without internal buffering (A6/A7, ESP8266, M590)
// need enough space in the buffer for the entire response
// else data will be lost (and the http library will fail).
#if !defined(TINY_GSM_RX_BUFFER)
#define TINY_GSM_RX_BUFFER 650
#endif

// See all AT commands, if wanted
// #define DUMP_AT_COMMANDS

// Define the serial console for debug prints, if needed
#define TINY_GSM_DEBUG SerialMon
// #define LOGGING  // <- Logging is for the HTTP library

// Range to attempt to autobaud
// NOTE:  DO NOT AUTOBAUD in production code.  Once you've established
// communication, set a fixed baud rate using modem.setBaud(#).
#define GSM_AUTOBAUD_MIN 9600
#define GSM_AUTOBAUD_MAX 115200

// Add a reception delay, if needed.
// This may be needed for a fast processor at a slow baud rate.
// #define TINY_GSM_YIELD() { delay(2); }

// Define how you're planning to connect to the internet
// These defines are only for this example; they are not needed in other code.
#define TINY_GSM_USE_GPRS true
#define TINY_GSM_USE_WIFI false

// set GSM PIN, if any
#define GSM_PIN ""

// Your GPRS credentials, if any
const char apn[]      = "sakura";
const char gprsUser[] = "";
const char gprsPass[] = "";

// Your WiFi connection credentials, if applicable
const char wifiSSID[] = "YourSSID";
const char wifiPass[] = "YourWiFiPass";

// Server details
const char server[]   = "vsh.pp.ua";
const char resource[] = "/TinyGSM/logo.txt";
const int  port       = 80;

#include <TinyGsmClient.h>
#include <ArduinoHttpClient.h>

// Just in case someone defined the wrong thing..
#if TINY_GSM_USE_GPRS && not defined TINY_GSM_MODEM_HAS_GPRS
#undef TINY_GSM_USE_GPRS
#undef TINY_GSM_USE_WIFI
#define TINY_GSM_USE_GPRS false
#define TINY_GSM_USE_WIFI true
#endif
#if TINY_GSM_USE_WIFI && not defined TINY_GSM_MODEM_HAS_WIFI
#undef TINY_GSM_USE_GPRS
#undef TINY_GSM_USE_WIFI
#define TINY_GSM_USE_GPRS true
#define TINY_GSM_USE_WIFI false
#endif

#ifdef DUMP_AT_COMMANDS
#include <StreamDebugger.h>
StreamDebugger debugger(SerialAT, SerialMon);
TinyGsm        modem(debugger);
#else
TinyGsm        modem(SerialAT);
#endif

TinyGsmClient client(modem);
HttpClient    http(client, server, port);
#define PWKEY 20

void setup() {
  // Set console baud rate
  SerialMon.begin(115200);
  delay(10);

  // !!!!!!!!!!!
  // Set your reset, enable, power pins here
  pinMode(PWKEY, OUTPUT);
  digitalWrite(PWKEY, HIGH);   // turn the LED on (HIGH is the voltage level)
  delay(2000);                       // wait for a second
  digitalWrite(PWKEY, LOW);    // turn the LED off by making the voltage LOW
  // !!!!!!!!!!!

  SerialMon.println("Wait...");

  // Set GSM module baud rate
  TinyGsmAutoBaud(SerialAT, GSM_AUTOBAUD_MIN, GSM_AUTOBAUD_MAX);
  // SerialAT.begin(9600);
  delay(6000);

  // Restart takes quite some time
  // To skip it, call init() instead of restart()
  SerialMon.println("Initializing modem...");
  modem.restart();
  // modem.init();

  String modemInfo = modem.getModemInfo();
  SerialMon.print("Modem Info: ");
  SerialMon.println(modemInfo);

#if TINY_GSM_USE_GPRS
  // Unlock your SIM card with a PIN if needed
  if (GSM_PIN && modem.getSimStatus() != 3) { modem.simUnlock(GSM_PIN); }
#endif
}

void loop() {
#if TINY_GSM_USE_WIFI
  // Wifi connection parameters must be set before waiting for the network
  SerialMon.print(F("Setting SSID/password..."));
  if (!modem.networkConnect(wifiSSID, wifiPass)) {
    SerialMon.println(" fail");
    delay(10000);
    return;
  }
  SerialMon.println(" success");
#endif

#if TINY_GSM_USE_GPRS && defined TINY_GSM_MODEM_XBEE
  // The XBee must run the gprsConnect function BEFORE waiting for network!
  modem.gprsConnect(apn, gprsUser, gprsPass);
#endif

  SerialMon.print("Waiting for network...");
  if (!modem.waitForNetwork()) {
    SerialMon.println(" fail");
    delay(10000);
    return;
  }
  SerialMon.println(" success");

  if (modem.isNetworkConnected()) { SerialMon.println("Network connected"); }

#if TINY_GSM_USE_GPRS
  // GPRS connection parameters are usually set after network registration
  SerialMon.print(F("Connecting to "));
  SerialMon.print(apn);
  if (!modem.gprsConnect(apn, gprsUser, gprsPass)) {
    SerialMon.println(" fail");
    delay(10000);
    return;
  }
  SerialMon.println(" success");

  if (modem.isGprsConnected()) { SerialMon.println("GPRS connected"); }
#endif

  SerialMon.print(F("Performing HTTP GET request... "));
  int err = http.get(resource);
  if (err != 0) {
    SerialMon.println(F("failed to connect"));
    delay(10000);
    return;
  }

  int status = http.responseStatusCode();
  SerialMon.print(F("Response status code: "));
  SerialMon.println(status);
  if (!status) {
    delay(10000);
    return;
  }

  SerialMon.println(F("Response Headers:"));
  while (http.headerAvailable()) {
    String headerName  = http.readHeaderName();
    String headerValue = http.readHeaderValue();
    SerialMon.println("    " + headerName + " : " + headerValue);
  }

  int length = http.contentLength();
  if (length >= 0) {
    SerialMon.print(F("Content length is: "));
    SerialMon.println(length);
  }
  if (http.isResponseChunked()) {
    SerialMon.println(F("The response is chunked"));
  }

  String body = http.responseBody();
  SerialMon.println(F("Response:"));
  SerialMon.println(body);

  SerialMon.print(F("Body length is: "));
  SerialMon.println(body.length());

  // Shutdown

  http.stop();
  SerialMon.println(F("Server disconnected"));

#if TINY_GSM_USE_WIFI
  modem.networkDisconnect();
  SerialMon.println(F("WiFi disconnected"));
#endif
#if TINY_GSM_USE_GPRS
  modem.gprsDisconnect();
  SerialMon.println(F("GPRS disconnected"));
#endif

  // Do nothing forevermore
  while (true) { delay(1000); }
}

通信ログ.txt

cxd56_farapiinitialize: Mismatched version: loader(20175) != Self(20585)
cxd56_farapiinitialize: Please update loader and gnssfw firmwares!!
Wait...
[2253] Trying baud rate 115200 ...
[5609] Modem responded at rate 115200
Initializing modem...
[42092] ### TinyGSM Version: 0.10.9
[42092] ### TinyGSM Compiled Module:  TinyGsmClientSIM7080
[42405] ### Modem: SIMCOM SIM7090
Modem Info: R1951.01
Waiting for network... success
Network connected
Connecting to sakura success
GPRS connected
Performing HTTP GET request... [46708] ### Got Data: 0
[46710] ### Closed:  0
Response status code: 200
Response Headers:
    Server : nginx/1.10.3 (Ubuntu)
    Date : Sun, 10 Oct 2021 05:27:44 GMT
    Content-Type : text/plain; charset=UTF-8
    Content-Length : 121
    Connection : close
    X-DNS-Prefetch-Control : off
    X-Frame-Options : SAMEORIGIN
    Strict-Transport-Security : max-age=15552000; includeSubDomains
    X-Download-Options : noopen
    X-Content-Type-Options : nosniff
    X-XSS-Protection : 1; mode=block
    Accept-Ranges : bytes
    Cache-Control : public, max-age=0
    Last-Modified : Wed, 27 Sep 2017 09:03:12 GMT
    ETag : W/"79-15ec2936080"
Content length is: 121
Response:

  _____            _____  _____  _____
    |  | |\ | \_/ |  ___ |_____ |  |  |
    |  | | \|  |  |_____| _____||  |  |


Body length is: 121
Server disconnected
GPRS disconnected

LTE-Mモジュールを小さく作れたので、いろいろと応用範囲が広がりそうです。