x よくわからないのでヘッダーもコピーしてください
x 長い

1.SCLとSDAを接続、プルアップも忘れずに
2.電源の接続
3.下記のソースコードを書き込む
4.コンパイル実行で表示されたら終了
5.おわり

注意
Mbed2のリビジョンは、125

忙しい人よう

main.cpp




//i2c_HT16K33_test1_767_1

#include "mbed.h"

#include "main.h"

#define ADDR        (0x70<<1)  //  address


DigitalOut myled(PB_0);


//I2C i2c(I2C_SDA, I2C_SCL); //767
//I2C i2c(PB_9, PB_8); //767


I2C_HandleTypeDef hi2c1;






void Error_Handler(void)
{
  __disable_irq();
  while (1)
  {
  }
}

#ifdef  USE_FULL_ASSERT
void assert_failed(uint8_t *file, uint32_t line)
{
}
#endif /* USE_FULL_ASSERT */







void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
  RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};

  /** Configure the main internal regulator output voltage
  */
  __HAL_RCC_PWR_CLK_ENABLE();
  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE3);
  /** Initializes the RCC Oscillators according to the specified parameters
  * in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }
  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK)
  {
    Error_Handler();
  }
  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_I2C1;
  PeriphClkInitStruct.I2c1ClockSelection = RCC_I2C1CLKSOURCE_PCLK1;
  if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK)
  {
    Error_Handler();
  }
}




static void MX_I2C1_Init(void)
{

  hi2c1.Instance = I2C1;
  hi2c1.Init.Timing = 0x00303D5B;
  hi2c1.Init.OwnAddress1 = 0;
  hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
  hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
  hi2c1.Init.OwnAddress2 = 0;
  hi2c1.Init.OwnAddress2Masks = I2C_OA2_NOMASK;
  hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
  hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
  if (HAL_I2C_Init(&hi2c1) != HAL_OK)
  {
    Error_Handler();
  }

  if (HAL_I2CEx_ConfigAnalogFilter(&hi2c1, I2C_ANALOGFILTER_ENABLE) != HAL_OK)
  {
    Error_Handler();
  }

  if (HAL_I2CEx_ConfigDigitalFilter(&hi2c1, 0) != HAL_OK)
  {
    Error_Handler();
  }

}



static void MX_GPIO_Init(void)
{
  __HAL_RCC_GPIOB_CLK_ENABLE();
}







void HAL_MspInit(void)
{

  __HAL_RCC_PWR_CLK_ENABLE();
  __HAL_RCC_SYSCFG_CLK_ENABLE();


}


void HAL_I2C_MspInit(I2C_HandleTypeDef* hi2c)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};
  if(hi2c->Instance==I2C1)
  {


    __HAL_RCC_GPIOB_CLK_ENABLE();
    /**I2C1 GPIO Configuration
    PB8     ------> I2C1_SCL
    PB9     ------> I2C1_SDA
    */
    GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_9;
    GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
    GPIO_InitStruct.Alternate = GPIO_AF4_I2C1;
    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

    __HAL_RCC_I2C1_CLK_ENABLE();

  }

}








int main() {


  HAL_Init();

  SystemClock_Config();
  MX_GPIO_Init();
  MX_I2C1_Init();


HAL_MspInit();

HAL_I2C_MspInit(&hi2c1);




    uint8_t buf[16];

    buf[0]=0x21;
    HAL_I2C_Master_Transmit(&hi2c1, ADDR, buf, 1, 3000);wait_ms(1);

    buf[0]=0x81;
    HAL_I2C_Master_Transmit(&hi2c1, ADDR, buf, 1, 3000);wait_ms(1);

    buf[0]=0xef;
    HAL_I2C_Master_Transmit(&hi2c1, ADDR, buf, 1, 3000);wait_ms(1);

    for(int ii=0;ii<16;ii++){
        buf[0]=ii;
        buf[1]=0x00;
        HAL_I2C_Master_Transmit(&hi2c1, ADDR, buf, 2, 3000);wait_ms(1);
    }//for

    while(1) {

        for(int ii=0;ii<8;ii++){

            buf[0]=0;
            buf[1]= (1<<ii);
            HAL_I2C_Master_Transmit(&hi2c1, ADDR, buf, 2, 3000);wait_ms(600);

        //myled = 1;
        HAL_GPIO_WritePin(GPIOB, GPIO_PIN_0, GPIO_PIN_SET);
        wait(0.2);
        //myled = 0;
        HAL_GPIO_WritePin(GPIOB, GPIO_PIN_0, GPIO_PIN_RESET);
        wait(0.2);


        }//for
    }//while



}//main

main.h



/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file           : main.h
  * @brief          : Header for main.c file.
  *                   This file contains the common defines of the application.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2022 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */
/* USER CODE END Header */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __MAIN_H
#define __MAIN_H

#ifdef __cplusplus
extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32f7xx_hal.h"

/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */

/* USER CODE END Includes */

/* Exported types ------------------------------------------------------------*/
/* USER CODE BEGIN ET */

/* USER CODE END ET */

/* Exported constants --------------------------------------------------------*/
/* USER CODE BEGIN EC */

/* USER CODE END EC */

/* Exported macro ------------------------------------------------------------*/
/* USER CODE BEGIN EM */

/* USER CODE END EM */

/* Exported functions prototypes ---------------------------------------------*/
void Error_Handler(void);

/* USER CODE BEGIN EFP */

/* USER CODE END EFP */

/* Private defines -----------------------------------------------------------*/
/* USER CODE BEGIN Private defines */

/* USER CODE END Private defines */

#ifdef __cplusplus
}
#endif

#endif /* __MAIN_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

stm32f7xx_hal_conf.h



/**
  ******************************************************************************
  * @file    stm32f7xx_hal_conf_template.h
  * @author  MCD Application Team
  * @brief   HAL configuration template file.
  *          This file should be copied to the application folder and renamed
  *          to stm32f7xx_hal_conf.h.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F7xx_HAL_CONF_H
#define __STM32F7xx_HAL_CONF_H

#ifdef __cplusplus
 extern "C" {
#endif

/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/

/* ########################## Module Selection ############################## */
/**
  * @brief This is the list of modules to be used in the HAL driver
  */
#define HAL_MODULE_ENABLED

  /* #define HAL_ADC_MODULE_ENABLED   */
/* #define HAL_CRYP_MODULE_ENABLED   */
/* #define HAL_CAN_MODULE_ENABLED   */
/* #define HAL_CEC_MODULE_ENABLED   */
/* #define HAL_CRC_MODULE_ENABLED   */
/* #define HAL_CRYP_MODULE_ENABLED   */
/* #define HAL_DAC_MODULE_ENABLED   */
/* #define HAL_DCMI_MODULE_ENABLED   */
/* #define HAL_DMA2D_MODULE_ENABLED   */
/* #define HAL_ETH_MODULE_ENABLED   */
/* #define HAL_NAND_MODULE_ENABLED   */
/* #define HAL_NOR_MODULE_ENABLED   */
/* #define HAL_SRAM_MODULE_ENABLED   */
/* #define HAL_SDRAM_MODULE_ENABLED   */
/* #define HAL_HASH_MODULE_ENABLED   */
/* #define HAL_I2S_MODULE_ENABLED   */
/* #define HAL_IWDG_MODULE_ENABLED   */
/* #define HAL_LPTIM_MODULE_ENABLED   */
/* #define HAL_LTDC_MODULE_ENABLED   */
/* #define HAL_QSPI_MODULE_ENABLED   */
/* #define HAL_RNG_MODULE_ENABLED   */
/* #define HAL_RTC_MODULE_ENABLED   */
/* #define HAL_SAI_MODULE_ENABLED   */
/* #define HAL_SD_MODULE_ENABLED   */
/* #define HAL_MMC_MODULE_ENABLED   */
/* #define HAL_SPDIFRX_MODULE_ENABLED   */
/* #define HAL_SPI_MODULE_ENABLED   */
/* #define HAL_TIM_MODULE_ENABLED   */
/* #define HAL_UART_MODULE_ENABLED   */
/* #define HAL_USART_MODULE_ENABLED   */
/* #define HAL_IRDA_MODULE_ENABLED   */
/* #define HAL_SMARTCARD_MODULE_ENABLED   */
/* #define HAL_WWDG_MODULE_ENABLED   */
/* #define HAL_PCD_MODULE_ENABLED   */
/* #define HAL_HCD_MODULE_ENABLED   */
/* #define HAL_DFSDM_MODULE_ENABLED   */
/* #define HAL_DSI_MODULE_ENABLED   */
/* #define HAL_JPEG_MODULE_ENABLED   */
/* #define HAL_MDIOS_MODULE_ENABLED   */
/* #define HAL_SMBUS_MODULE_ENABLED   */
/* #define HAL_EXTI_MODULE_ENABLED   */
#define HAL_GPIO_MODULE_ENABLED
#define HAL_EXTI_MODULE_ENABLED
#define HAL_DMA_MODULE_ENABLED
#define HAL_RCC_MODULE_ENABLED
#define HAL_FLASH_MODULE_ENABLED
#define HAL_PWR_MODULE_ENABLED
#define HAL_I2C_MODULE_ENABLED
#define HAL_CORTEX_MODULE_ENABLED

/* ########################## HSE/HSI Values adaptation ##################### */
/**
  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
  *        This value is used by the RCC HAL module to compute the system frequency
  *        (when HSE is used as system clock source, directly or through the PLL).
  */
#if !defined  (HSE_VALUE)
  #define HSE_VALUE    ((uint32_t)25000000U) /*!< Value of the External oscillator in Hz */
#endif /* HSE_VALUE */

#if !defined  (HSE_STARTUP_TIMEOUT)
  #define HSE_STARTUP_TIMEOUT    ((uint32_t)100U)   /*!< Time out for HSE start up, in ms */
#endif /* HSE_STARTUP_TIMEOUT */

/**
  * @brief Internal High Speed oscillator (HSI) value.
  *        This value is used by the RCC HAL module to compute the system frequency
  *        (when HSI is used as system clock source, directly or through the PLL).
  */
#if !defined  (HSI_VALUE)
  #define HSI_VALUE    ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
#endif /* HSI_VALUE */

/**
  * @brief Internal Low Speed oscillator (LSI) value.
  */
#if !defined  (LSI_VALUE)
 #define LSI_VALUE  ((uint32_t)32000U)       /*!< LSI Typical Value in Hz*/
#endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz
                                             The real value may vary depending on the variations
                                             in voltage and temperature.  */
/**
  * @brief External Low Speed oscillator (LSE) value.
  */
#if !defined  (LSE_VALUE)
 #define LSE_VALUE  ((uint32_t)32768U)    /*!< Value of the External Low Speed oscillator in Hz */
#endif /* LSE_VALUE */

#if !defined  (LSE_STARTUP_TIMEOUT)
  #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000U)   /*!< Time out for LSE start up, in ms */
#endif /* LSE_STARTUP_TIMEOUT */

/**
  * @brief External clock source for I2S peripheral
  *        This value is used by the I2S HAL module to compute the I2S clock source
  *        frequency, this source is inserted directly through I2S_CKIN pad.
  */
#if !defined  (EXTERNAL_CLOCK_VALUE)
  #define EXTERNAL_CLOCK_VALUE    ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/
#endif /* EXTERNAL_CLOCK_VALUE */

/* Tip: To avoid modifying this file each time you need to use different HSE,
   ===  you can define the HSE value in your toolchain compiler preprocessor. */

/* ########################### System Configuration ######################### */
/**
  * @brief This is the HAL system configuration section
  */
#define  VDD_VALUE                    ((uint32_t)3300U) /*!< Value of VDD in mv */
#define  TICK_INT_PRIORITY            ((uint32_t)0U) /*!< tick interrupt priority */
#define  USE_RTOS                     0U
#define  PREFETCH_ENABLE              0U
#define  ART_ACCLERATOR_ENABLE        0U /* To enable instruction cache and prefetch */

#define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
#define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
#define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
#define  USE_HAL_CRYP_REGISTER_CALLBACKS        0U /* CRYP register callback disabled      */
#define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
#define  USE_HAL_DCMI_REGISTER_CALLBACKS        0U /* DCMI register callback disabled      */
#define  USE_HAL_DFSDM_REGISTER_CALLBACKS       0U /* DFSDM register callback disabled     */
#define  USE_HAL_DMA2D_REGISTER_CALLBACKS       0U /* DMA2D register callback disabled     */
#define  USE_HAL_DSI_REGISTER_CALLBACKS         0U /* DSI register callback disabled       */
#define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
#define  USE_HAL_HASH_REGISTER_CALLBACKS        0U /* HASH register callback disabled      */
#define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
#define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
#define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
#define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
#define  USE_HAL_JPEG_REGISTER_CALLBACKS        0U /* JPEG register callback disabled      */
#define  USE_HAL_LPTIM_REGISTER_CALLBACKS       0U /* LPTIM register callback disabled     */
#define  USE_HAL_LTDC_REGISTER_CALLBACKS        0U /* LTDC register callback disabled      */
#define  USE_HAL_MDIOS_REGISTER_CALLBACKS       0U /* MDIOS register callback disabled     */
#define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
#define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
#define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
#define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
#define  USE_HAL_QSPI_REGISTER_CALLBACKS        0U /* QSPI register callback disabled      */
#define  USE_HAL_RNG_REGISTER_CALLBACKS         0U /* RNG register callback disabled       */
#define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
#define  USE_HAL_SAI_REGISTER_CALLBACKS         0U /* SAI register callback disabled       */
#define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
#define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
#define  USE_HAL_SDRAM_REGISTER_CALLBACKS       0U /* SDRAM register callback disabled     */
#define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
#define  USE_HAL_SPDIFRX_REGISTER_CALLBACKS     0U /* SPDIFRX register callback disabled   */
#define  USE_HAL_SMBUS_REGISTER_CALLBACKS       0U /* SMBUS register callback disabled     */
#define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
#define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
#define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
#define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
#define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */

/* ########################## Assert Selection ############################## */
/**
  * @brief Uncomment the line below to expanse the "assert_param" macro in the
  *        HAL drivers code
  */
/* #define USE_FULL_ASSERT    1U */

/* ################## Ethernet peripheral configuration ##################### */

/* Section 1 : Ethernet peripheral configuration */

/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
#define MAC_ADDR0   2U
#define MAC_ADDR1   0U
#define MAC_ADDR2   0U
#define MAC_ADDR3   0U
#define MAC_ADDR4   0U
#define MAC_ADDR5   0U

/* Definition of the Ethernet driver buffers size and count */
#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
#define ETH_RXBUFNB                    ((uint32_t)4U)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
#define ETH_TXBUFNB                    ((uint32_t)4U)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */

/* Section 2: PHY configuration section */

/* DP83848_PHY_ADDRESS Address*/
#define DP83848_PHY_ADDRESS           0x01U
/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
#define PHY_RESET_DELAY                 ((uint32_t)0x000000FFU)
/* PHY Configuration delay */
#define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFFU)

#define PHY_READ_TO                     ((uint32_t)0x0000FFFFU)
#define PHY_WRITE_TO                    ((uint32_t)0x0000FFFFU)

/* Section 3: Common PHY Registers */

#define PHY_BCR                         ((uint16_t)0x0000U)    /*!< Transceiver Basic Control Register   */
#define PHY_BSR                         ((uint16_t)0x0001U)    /*!< Transceiver Basic Status Register    */

#define PHY_RESET                       ((uint16_t)0x8000U)  /*!< PHY Reset */
#define PHY_LOOPBACK                    ((uint16_t)0x4000U)  /*!< Select loop-back mode */
#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100U)  /*!< Set the full-duplex mode at 100 Mb/s */
#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000U)  /*!< Set the half-duplex mode at 100 Mb/s */
#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100U)  /*!< Set the full-duplex mode at 10 Mb/s  */
#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000U)  /*!< Set the half-duplex mode at 10 Mb/s  */
#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000U)  /*!< Enable auto-negotiation function     */
#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200U)  /*!< Restart auto-negotiation function    */
#define PHY_POWERDOWN                   ((uint16_t)0x0800U)  /*!< Select the power down mode           */
#define PHY_ISOLATE                     ((uint16_t)0x0400U)  /*!< Isolate PHY from MII                 */

#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020U)  /*!< Auto-Negotiation process completed   */
#define PHY_LINKED_STATUS               ((uint16_t)0x0004U)  /*!< Valid link established               */
#define PHY_JABBER_DETECTION            ((uint16_t)0x0002U)  /*!< Jabber condition detected            */

/* Section 4: Extended PHY Registers */
#define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */

#define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */

/* ################## SPI peripheral configuration ########################## */

/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
* Activated: CRC code is present inside driver
* Deactivated: CRC code cleaned from driver
*/

#define USE_SPI_CRC                     0U

/* Includes ------------------------------------------------------------------*/
/**
  * @brief Include module's header file
  */

#ifdef HAL_RCC_MODULE_ENABLED
  #include "stm32f7xx_hal_rcc.h"
#endif /* HAL_RCC_MODULE_ENABLED */

#ifdef HAL_EXTI_MODULE_ENABLED
  #include "stm32f7xx_hal_exti.h"
#endif /* HAL_EXTI_MODULE_ENABLED */

#ifdef HAL_GPIO_MODULE_ENABLED
  #include "stm32f7xx_hal_gpio.h"
#endif /* HAL_GPIO_MODULE_ENABLED */

#ifdef HAL_DMA_MODULE_ENABLED
  #include "stm32f7xx_hal_dma.h"
#endif /* HAL_DMA_MODULE_ENABLED */

#ifdef HAL_CORTEX_MODULE_ENABLED
  #include "stm32f7xx_hal_cortex.h"
#endif /* HAL_CORTEX_MODULE_ENABLED */

#ifdef HAL_ADC_MODULE_ENABLED
  #include "stm32f7xx_hal_adc.h"
#endif /* HAL_ADC_MODULE_ENABLED */

#ifdef HAL_CAN_MODULE_ENABLED
  #include "stm32f7xx_hal_can.h"
#endif /* HAL_CAN_MODULE_ENABLED */

#ifdef HAL_CEC_MODULE_ENABLED
  #include "stm32f7xx_hal_cec.h"
#endif /* HAL_CEC_MODULE_ENABLED */

#ifdef HAL_CRC_MODULE_ENABLED
  #include "stm32f7xx_hal_crc.h"
#endif /* HAL_CRC_MODULE_ENABLED */

#ifdef HAL_CRYP_MODULE_ENABLED
  #include "stm32f7xx_hal_cryp.h"
#endif /* HAL_CRYP_MODULE_ENABLED */

#ifdef HAL_DMA2D_MODULE_ENABLED
  #include "stm32f7xx_hal_dma2d.h"
#endif /* HAL_DMA2D_MODULE_ENABLED */

#ifdef HAL_DAC_MODULE_ENABLED
  #include "stm32f7xx_hal_dac.h"
#endif /* HAL_DAC_MODULE_ENABLED */

#ifdef HAL_DCMI_MODULE_ENABLED
  #include "stm32f7xx_hal_dcmi.h"
#endif /* HAL_DCMI_MODULE_ENABLED */

#ifdef HAL_ETH_MODULE_ENABLED
  #include "stm32f7xx_hal_eth.h"
#endif /* HAL_ETH_MODULE_ENABLED */

#ifdef HAL_FLASH_MODULE_ENABLED
  #include "stm32f7xx_hal_flash.h"
#endif /* HAL_FLASH_MODULE_ENABLED */

#ifdef HAL_SRAM_MODULE_ENABLED
  #include "stm32f7xx_hal_sram.h"
#endif /* HAL_SRAM_MODULE_ENABLED */

#ifdef HAL_NOR_MODULE_ENABLED
  #include "stm32f7xx_hal_nor.h"
#endif /* HAL_NOR_MODULE_ENABLED */

#ifdef HAL_NAND_MODULE_ENABLED
  #include "stm32f7xx_hal_nand.h"
#endif /* HAL_NAND_MODULE_ENABLED */

#ifdef HAL_SDRAM_MODULE_ENABLED
  #include "stm32f7xx_hal_sdram.h"
#endif /* HAL_SDRAM_MODULE_ENABLED */

#ifdef HAL_HASH_MODULE_ENABLED
 #include "stm32f7xx_hal_hash.h"
#endif /* HAL_HASH_MODULE_ENABLED */

#ifdef HAL_I2C_MODULE_ENABLED
 #include "stm32f7xx_hal_i2c.h"
#endif /* HAL_I2C_MODULE_ENABLED */

#ifdef HAL_I2S_MODULE_ENABLED
 #include "stm32f7xx_hal_i2s.h"
#endif /* HAL_I2S_MODULE_ENABLED */

#ifdef HAL_IWDG_MODULE_ENABLED
 #include "stm32f7xx_hal_iwdg.h"
#endif /* HAL_IWDG_MODULE_ENABLED */

#ifdef HAL_LPTIM_MODULE_ENABLED
 #include "stm32f7xx_hal_lptim.h"
#endif /* HAL_LPTIM_MODULE_ENABLED */

#ifdef HAL_LTDC_MODULE_ENABLED
 #include "stm32f7xx_hal_ltdc.h"
#endif /* HAL_LTDC_MODULE_ENABLED */

#ifdef HAL_PWR_MODULE_ENABLED
 #include "stm32f7xx_hal_pwr.h"
#endif /* HAL_PWR_MODULE_ENABLED */

#ifdef HAL_QSPI_MODULE_ENABLED
 #include "stm32f7xx_hal_qspi.h"
#endif /* HAL_QSPI_MODULE_ENABLED */

#ifdef HAL_RNG_MODULE_ENABLED
 #include "stm32f7xx_hal_rng.h"
#endif /* HAL_RNG_MODULE_ENABLED */

#ifdef HAL_RTC_MODULE_ENABLED
 #include "stm32f7xx_hal_rtc.h"
#endif /* HAL_RTC_MODULE_ENABLED */

#ifdef HAL_SAI_MODULE_ENABLED
 #include "stm32f7xx_hal_sai.h"
#endif /* HAL_SAI_MODULE_ENABLED */

#ifdef HAL_SD_MODULE_ENABLED
 #include "stm32f7xx_hal_sd.h"
#endif /* HAL_SD_MODULE_ENABLED */

#ifdef HAL_MMC_MODULE_ENABLED
 #include "stm32f7xx_hal_mmc.h"
#endif /* HAL_MMC_MODULE_ENABLED */

#ifdef HAL_SPDIFRX_MODULE_ENABLED
 #include "stm32f7xx_hal_spdifrx.h"
#endif /* HAL_SPDIFRX_MODULE_ENABLED */

#ifdef HAL_SPI_MODULE_ENABLED
 #include "stm32f7xx_hal_spi.h"
#endif /* HAL_SPI_MODULE_ENABLED */

#ifdef HAL_TIM_MODULE_ENABLED
 #include "stm32f7xx_hal_tim.h"
#endif /* HAL_TIM_MODULE_ENABLED */

#ifdef HAL_UART_MODULE_ENABLED
 #include "stm32f7xx_hal_uart.h"
#endif /* HAL_UART_MODULE_ENABLED */

#ifdef HAL_USART_MODULE_ENABLED
 #include "stm32f7xx_hal_usart.h"
#endif /* HAL_USART_MODULE_ENABLED */

#ifdef HAL_IRDA_MODULE_ENABLED
 #include "stm32f7xx_hal_irda.h"
#endif /* HAL_IRDA_MODULE_ENABLED */

#ifdef HAL_SMARTCARD_MODULE_ENABLED
 #include "stm32f7xx_hal_smartcard.h"
#endif /* HAL_SMARTCARD_MODULE_ENABLED */

#ifdef HAL_WWDG_MODULE_ENABLED
 #include "stm32f7xx_hal_wwdg.h"
#endif /* HAL_WWDG_MODULE_ENABLED */

#ifdef HAL_PCD_MODULE_ENABLED
 #include "stm32f7xx_hal_pcd.h"
#endif /* HAL_PCD_MODULE_ENABLED */

#ifdef HAL_HCD_MODULE_ENABLED
 #include "stm32f7xx_hal_hcd.h"
#endif /* HAL_HCD_MODULE_ENABLED */

#ifdef HAL_DFSDM_MODULE_ENABLED
 #include "stm32f7xx_hal_dfsdm.h"
#endif /* HAL_DFSDM_MODULE_ENABLED */

#ifdef HAL_DSI_MODULE_ENABLED
 #include "stm32f7xx_hal_dsi.h"
#endif /* HAL_DSI_MODULE_ENABLED */

#ifdef HAL_JPEG_MODULE_ENABLED
 #include "stm32f7xx_hal_jpeg.h"
#endif /* HAL_JPEG_MODULE_ENABLED */

#ifdef HAL_MDIOS_MODULE_ENABLED
 #include "stm32f7xx_hal_mdios.h"
#endif /* HAL_MDIOS_MODULE_ENABLED */

#ifdef HAL_SMBUS_MODULE_ENABLED
 #include "stm32f7xx_hal_smbus.h"
#endif /* HAL_SMBUS_MODULE_ENABLED */

/* Exported macro ------------------------------------------------------------*/
#ifdef  USE_FULL_ASSERT
/**
  * @brief  The assert_param macro is used for function's parameters check.
  * @param  expr: If expr is false, it calls assert_failed function
  *         which reports the name of the source file and the source
  *         line number of the call that failed.
  *         If expr is true, it returns no value.
  * @retval None
  */
  #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
/* Exported functions ------------------------------------------------------- */
  void assert_failed(uint8_t* file, uint32_t line);
#else
  #define assert_param(expr) ((void)0U)
#endif /* USE_FULL_ASSERT */

#ifdef __cplusplus
}
#endif

#endif /* __STM32F7xx_HAL_CONF_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

stm32f7xx_it.h




/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file    stm32f7xx_it.h
  * @brief   This file contains the headers of the interrupt handlers.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2022 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
 ******************************************************************************
  */
/* USER CODE END Header */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F7xx_IT_H
#define __STM32F7xx_IT_H

#ifdef __cplusplus
 extern "C" {
#endif

/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */

/* USER CODE END Includes */

/* Exported types ------------------------------------------------------------*/
/* USER CODE BEGIN ET */

/* USER CODE END ET */

/* Exported constants --------------------------------------------------------*/
/* USER CODE BEGIN EC */

/* USER CODE END EC */

/* Exported macro ------------------------------------------------------------*/
/* USER CODE BEGIN EM */

/* USER CODE END EM */

/* Exported functions prototypes ---------------------------------------------*/
void NMI_Handler(void);
void HardFault_Handler(void);
void MemManage_Handler(void);
void BusFault_Handler(void);
void UsageFault_Handler(void);
void SVC_Handler(void);
void DebugMon_Handler(void);
void PendSV_Handler(void);
void SysTick_Handler(void);
/* USER CODE BEGIN EFP */

/* USER CODE END EFP */

#ifdef __cplusplus
}
#endif

#endif /* __STM32F7xx_IT_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/