概要

Seeed studio XIAO nRF52840SenseのFlash Memoryを使いたい。
ただ、参考になる日本語のサイトが無いので、Seeedのページを参考にしながら実装してみた。

開発環境

VS Code + Platformio

はじめに

趣味で電子工作をしており、充電モジュール&ローバット検知モジュールがついているSeeed studio XIAO nRF52840Senseを触っている。
データをFlash Memory上にためたいが、どうやればいいのかわからなかった。

VS Codeの設定

Platformioから、以下のようにBoard、Frameworkを選ぶ。

コーディング

のコードを貼り付ける。

このままだとエラーがでるので、
Arduino.hとnrf52840.hをインクルードする。
また、このままだとQSIP_Configure_Memory()がnot defineというエラーがでるので、QSPI_Initialise()の前にQSIP_Configure_Memory()を持ってくる。

これでコンパイルエラーがなくなって書き込めるはず。

これで書き込めはするのですが、VS Code上ではよくわからないエラーが出ます。

これを解消するには、.vscodeフォルダの中のc_cpp_properties.jsonのconfigurationsのdefineに"__STATIC_INLINE= static inline",を追加してください。そうすればエラーが出なくなると思います。

最終的なコードは以下の通り。

#include <Arduino.h>
#include <stdio.h>
#include <string.h>
#include <stdlib.h>
#include <nrf52840.h>
#include "nrfx_qspi.h"
#include "app_util_platform.h"
#include "nrf_log.h"
#include "nrf_log_ctrl.h"
#include "nrf_log_default_backends.h"
#include "sdk_config.h"
#include "nrf_delay.h"
#include "avr/interrupt.h"

/*
 * Strange parts of this code ... Or things I don't understand
 *
 * After the first READ in Setup() it successfully reads the data (Returns 0 = NRFX_SUCCESS), but the status flag
 * has the top 8 bits set to 0xFF which causes nrfx_qspi_mem_busy_check() to show 17 (Returns 17 = NRFX_ERROR_BUSY).
 * However masking the STATUS register with 8 reveals the Ready Status = 1, QSPI is ready!
 * This was why I wrote the QSPI_IsReady().
 *
 * nrf_qspi_phy_conf_t not visible as a structure if you try and set it like this :
 *   QSPIConfig.phy_if {
 *     .xxx = yyy,
 *     .aaa = bbb
 *   };
 *
 * I don't know what the significance of the 48ms Deep Power-down Mode (DPM) is.
 * Will it go into DPM if not used for 48ms and then take 48ms to wake up if instructed?
 *
 * Hope you enjoy this little snippet of code!  Feel free to butcher and use it.
 * Thanks to JM_Laird and Haakonish in Case ID: 224515.
 * And, yes, I could have made it neater, but really need to add some of the bits into a project and tidy them up there!
 */

// QSPI Settings
#define QSPI_STD_CMD_WRSR 0x01
#define QSPI_STD_CMD_RSTEN 0x66
#define QSPI_STD_CMD_RST 0x99
#define QSPI_DPM_ENTER 0x0003 // 3 x 256 x 62.5ns = 48ms
#define QSPI_DPM_EXIT 0x0003

static uint32_t *QSPI_Status_Ptr = (uint32_t *)0x40029604; // Setup for the SEEED XIAO BLE - nRF52840
static nrfx_qspi_config_t QSPIConfig;
static nrf_qspi_cinstr_conf_t QSPICinstr_cfg;
static const uint32_t MemToUse = 64 * 1024; // Alter this to create larger read writes, 64Kb is the size of the Erase
static bool Debug_On = true;
static uint16_t pBuf[MemToUse / 2] = {0}; // 16bit used as that is what this memory is going to be used for
static uint32_t *BufMem = (uint32_t *)&pBuf;
static bool QSPIWait = false;
// QSPI Settings Complete

static void qspi_handler(nrfx_qspi_evt_t event, void *p_context)
{
  // UNUSED_PARAMETER(p_context);
  // Serial.println("QSPI Interrupt");
  // if (event == NRFX_QSPI_EVENT_DONE) {
  //   QSPI_HasFinished = true;
  // }
}

static void QSPI_Status(char ASender[])
{ // Prints the QSPI Status
  Serial.print("(");
  Serial.print(ASender);
  Serial.print(") QSPI is busy/idle ... Result = ");
  Serial.println(nrfx_qspi_mem_busy_check() & 8);
  Serial.print("(");
  Serial.print(ASender);
  Serial.print(") QSPI Status flag = 0x");
  Serial.print(NRF_QSPI->STATUS, HEX);
  Serial.print(" (from NRF_QSPI) or 0x");
  Serial.print(*QSPI_Status_Ptr, HEX);
  Serial.println(" (from *QSPI_Status_Ptr)");
}

static void QSPI_PrintData(uint16_t *AnAddress, uint32_t AnAmount)
{
  uint32_t i;

  Serial.print("Data :");
  for (i = 0; i < AnAmount; i++)
  {
    Serial.print(" 0x");
    Serial.print(*(AnAddress + i), HEX);
  }
  Serial.println("");
}

static nrfx_err_t QSPI_IsReady()
{
  if (((*QSPI_Status_Ptr & 8) == 8) && (*QSPI_Status_Ptr & 0x01000000) == 0)
  {
    return NRFX_SUCCESS;
  }
  else
  {
    return NRFX_ERROR_BUSY;
  }
}

static nrfx_err_t QSPI_WaitForReady()
{
  while (QSPI_IsReady() == NRFX_ERROR_BUSY)
  {
    if (Debug_On)
    {
      Serial.print("*QSPI_Status_Ptr & 8 = ");
      Serial.print(*QSPI_Status_Ptr & 8);
      Serial.print(", *QSPI_Status_Ptr & 0x01000000 = 0x");
      Serial.println(*QSPI_Status_Ptr & 0x01000000, HEX);
      QSPI_Status("QSPI_WaitForReady");
    }
  }
  return NRFX_SUCCESS;
}

static void QSIP_Configure_Memory()
{
  // uint8_t  temporary = 0x40;
  uint8_t temporary[] = {0x00, 0x02};
  uint32_t Error_Code;

  QSPICinstr_cfg = {
      .opcode = QSPI_STD_CMD_RSTEN,
      .length = NRF_QSPI_CINSTR_LEN_1B,
      .io2_level = true,
      .io3_level = true,
      .wipwait = QSPIWait,
      .wren = true};
  QSPI_WaitForReady();
  if (nrfx_qspi_cinstr_xfer(&QSPICinstr_cfg, NULL, NULL) != NRFX_SUCCESS)
  { // Send reset enable
    if (Debug_On)
    {
      Serial.println("(QSIP_Configure_Memory) QSPI 'Send reset enable' failed!");
    }
  }
  else
  {
    QSPICinstr_cfg.opcode = QSPI_STD_CMD_RST;
    QSPI_WaitForReady();
    if (nrfx_qspi_cinstr_xfer(&QSPICinstr_cfg, NULL, NULL) != NRFX_SUCCESS)
    { // Send reset command
      if (Debug_On)
      {
        Serial.println("(QSIP_Configure_Memory) QSPI Reset failed!");
      }
    }
    else
    {
      QSPICinstr_cfg.opcode = QSPI_STD_CMD_WRSR;
      QSPICinstr_cfg.length = NRF_QSPI_CINSTR_LEN_3B;
      QSPI_WaitForReady();
      if (nrfx_qspi_cinstr_xfer(&QSPICinstr_cfg, &temporary, NULL) != NRFX_SUCCESS)
      { // Switch to qspi mode
        if (Debug_On)
        {
          Serial.println("(QSIP_Configure_Memory) QSPI failed to switch to QSPI mode!");
        }
      }
      else
      {
        QSPI_Status("QSIP_Configure_Memory");
      }
    }
  }
}

static nrfx_err_t QSPI_Initialise()
{ // Initialises the QSPI and NRF LOG
  uint32_t Error_Code;

  NRF_LOG_INIT(NULL); // Initialise the NRF Log
  NRF_LOG_DEFAULT_BACKENDS_INIT();
  // QSPI Config
  QSPIConfig.xip_offset = NRFX_QSPI_CONFIG_XIP_OFFSET;
  QSPIConfig.pins = {
      // Setup for the SEEED XIAO BLE - nRF52840
      .sck_pin = 21,
      .csn_pin = 25,
      .io0_pin = 20,
      .io1_pin = 24,
      .io2_pin = 22,
      .io3_pin = 23,
  };
  QSPIConfig.irq_priority = (uint8_t)NRFX_QSPI_CONFIG_IRQ_PRIORITY;
  QSPIConfig.prot_if = {
      // .readoc     = (nrf_qspi_readoc_t)NRFX_QSPI_CONFIG_READOC,
      .readoc = (nrf_qspi_readoc_t)NRF_QSPI_READOC_READ4O,
      // .writeoc    = (nrf_qspi_writeoc_t)NRFX_QSPI_CONFIG_WRITEOC,
      .writeoc = (nrf_qspi_writeoc_t)NRF_QSPI_WRITEOC_PP4O,
      .addrmode = (nrf_qspi_addrmode_t)NRFX_QSPI_CONFIG_ADDRMODE,
      .dpmconfig = false,
  };
  QSPIConfig.phy_if.sck_freq = (nrf_qspi_frequency_t)NRF_QSPI_FREQ_32MDIV1; // I had to do it this way as it complained about nrf_qspi_phy_conf_t not being visible
  // QSPIConfig.phy_if.sck_freq   = (nrf_qspi_frequency_t)NRFX_QSPI_CONFIG_FREQUENCY;
  QSPIConfig.phy_if.spi_mode = (nrf_qspi_spi_mode_t)NRFX_QSPI_CONFIG_MODE;
  QSPIConfig.phy_if.dpmen = false;
  // QSPI Config Complete
  // Setup QSPI to allow for DPM but with it turned off
  QSPIConfig.prot_if.dpmconfig = true;
  NRF_QSPI->DPMDUR = (QSPI_DPM_ENTER << 16) | QSPI_DPM_EXIT; // Found this on the Nordic Q&A pages, Sets the Deep power-down mode timer
  Error_Code = 1;
  while (Error_Code != 0)
  {
    Error_Code = nrfx_qspi_init(&QSPIConfig, NULL, NULL);
    if (Error_Code != NRFX_SUCCESS)
    {
      if (Debug_On)
      {
        Serial.print("(QSPI_Initialise) nrfx_qspi_init returned : ");
        Serial.println(Error_Code);
      }
    }
    else
    {
      if (Debug_On)
      {
        Serial.println("(QSPI_Initialise) nrfx_qspi_init successful");
      }
    }
  }
  QSPI_Status("QSPI_Initialise (Before QSIP_Configure_Memory)");
  QSIP_Configure_Memory();
  if (Debug_On)
  {
    Serial.println("(QSPI_Initialise) Wait for QSPI to be ready ...");
  }
  NRF_QSPI->TASKS_ACTIVATE = 1;
  QSPI_WaitForReady();
  if (Debug_On)
  {
    Serial.println("(QSPI_Initialise) QSPI is ready");
  }
  return QSPI_IsReady();
}

static void QSPI_Erase(uint32_t AStartAddress)
{
  uint32_t TimeTaken;
  bool QSPIReady = false;
  bool AlreadyPrinted = false;

  if (Debug_On)
  {
    Serial.println("(QSPI_Erase) Erasing memory");
  }
  while (!QSPIReady)
  {
    if (QSPI_IsReady() != NRFX_SUCCESS)
    {
      if (!AlreadyPrinted)
      {
        QSPI_Status("QSPI_Erase (Waiting)");
        AlreadyPrinted = true;
      }
    }
    else
    {
      QSPIReady = true;
      QSPI_Status("QSPI_Erase (Waiting Loop Breakout)");
    }
  }
  if (Debug_On)
  {
    QSPI_Status("QSPI_Erase (Finished Waiting)");
    TimeTaken = millis();
  }
  if (nrfx_qspi_erase(NRF_QSPI_ERASE_LEN_64KB, AStartAddress) != NRFX_SUCCESS)
  {
    if (Debug_On)
    {
      Serial.print("(QSPI_Initialise_Page) QSPI Address 0x");
      Serial.print(AStartAddress, HEX);
      Serial.println(" failed to erase!");
    }
  }
  else
  {
    if (Debug_On)
    {
      TimeTaken = millis() - TimeTaken;
      Serial.print("(QSPI_Initialise_Page) QSPI took ");
      Serial.print(TimeTaken);
      Serial.println("ms to erase a 64Kb page");
    }
  }
}

void setup()
{
  uint32_t Error_Code;
  uint32_t TimeTaken;
  uint16_t i;

  delay(10000);
  Serial.begin(9600);
  while (!Serial)
  {
  }

  if (Debug_On)
  {
    Serial.println("(Setup) QSPI Initialising ...");
  }
  if (QSPI_Initialise() != NRFX_SUCCESS)
  {
    if (Debug_On)
    {
      Serial.println("(Setup) QSPI Memory failed to start!");
    }
  }
  else
  {
    if (Debug_On)
    {
      Serial.println("(Setup) QSPI initialised and ready");
      QSPI_Status("Setup (After initialise)");
    }
  }

  if (Debug_On)
  {
    Serial.print("(Setup) QSPI is about to be read and then erased. Current busy state is = ");
    Serial.println(QSPI_IsReady());
  }

  // QSPI Speed Test
  if (Debug_On)
  {
    QSPI_Status("Setup (Before read)");
    TimeTaken = millis();
  }
  Error_Code = nrfx_qspi_read(pBuf, MemToUse, 0x0);
  if (Debug_On)
  {
    TimeTaken = millis() - TimeTaken;
    Serial.print("(Setup) QSPI took ");
    Serial.print(TimeTaken);
    Serial.print("ms to read ");
    Serial.print(MemToUse / 1024);
    Serial.print("Kb ... Read result = ");
    Serial.println(Error_Code);
    QSPI_Status("Setup (After read)");
    QSPI_WaitForReady();
    QSPI_PrintData(&pBuf[0], 10);
  }
  if (Debug_On)
  {
    Serial.println("QSPI Erasing 64Kb of memory");
  }
  QSPI_Erase(0);
  if (Debug_On)
  {
    Serial.println("(Setup) QSPI read after erase");
    TimeTaken = millis();
  }
  QSPI_WaitForReady();
  Error_Code = nrfx_qspi_read(pBuf, MemToUse, 0x0);
  if (Debug_On)
  {
    TimeTaken = millis() - TimeTaken;
    Serial.print("(Setup) QSPI took ");
    Serial.print(TimeTaken);
    Serial.print("ms to read ");
    Serial.print(MemToUse / 1024);
    Serial.print("Kb ... Read result = ");
    Serial.println(Error_Code);
    QSPI_WaitForReady();
    QSPI_PrintData(&pBuf[0], 10);
  }
  for (i = 0; i < MemToUse / 2; i++)
  {
    pBuf[i] = i * 2;
  }
  QSPI_WaitForReady();
  if (Debug_On)
  {
    Serial.println("(Setup) Just before QSPI write");
    TimeTaken = millis();
  }
  Error_Code = nrfx_qspi_write(pBuf, MemToUse, 0x0);
  if (Debug_On)
  {
    TimeTaken = millis() - TimeTaken;
    Serial.print("(Setup) QSPI took ");
    Serial.print(TimeTaken);
    Serial.print("ms to write ");
    Serial.print(MemToUse / 1024);
    Serial.print("Kb ... Write result = ");
    Serial.println(Error_Code);
  }
  QSPI_WaitForReady();
  if (Debug_On)
  {
    Serial.println("(Setup) Just before QSPI read");
    TimeTaken = millis();
  }
  Error_Code = nrfx_qspi_read(pBuf, MemToUse, 0x0);
  if (Debug_On)
  {
    TimeTaken = millis() - TimeTaken;
    Serial.print("(Setup) QSPI took ");
    Serial.print(TimeTaken);
    Serial.print("ms to read ");
    Serial.print(MemToUse / 1024);
    Serial.print("Kb ... Read result = ");
    Serial.println(Error_Code);
    QSPI_WaitForReady();
    QSPI_PrintData(&pBuf[0], 10);
  }
  QSPI_WaitForReady();
  QSPI_Status("Setup");
  // QSPI Speed Test Complete
}

void loop()
{
  delay(10000);
}

ちょっとしたメモ

nrfx_qspi_writeでデータの書き込みができるのだが、QSPI_Eraseをしないと書き込みできないっぽい。

これからやりたいこと

充電制御、ローバット検知
ArduinoBLEを用いたBLE通信
マルチタスク制御

最後に

nRF52840 Senseは低消費かつ充電モジュール&ローバット検知モジュールがついているマイコンボードなので、非常に使い勝手は良いと思います。これからも情報発信していたいと思います。