前回まで、PICとRPI4Bのuart通信を実施しました。PIC側では、ｷｬﾗｸﾀｰlcdに受信文字を表示し、受信文字のspi-sramへの書込み・読み出しを確認し、ハードウェアーpwmを使ってLEDの明るさを変えてみました。

今回は、このハードウェアーpwmを使って、PIC側でDC-motorを動かしてみます。直接では電流容量的に無理なので、DC-motorドライバーのTI社製DRV8835を使いました。

配線図です。DRV8835はロジック電源(Vcc)とモーター動力電源(VM)が分かれています。2電源ありますから、両方にダイオードを追加しています。GNDは共通です。コイルも抵抗も入れていません。ブラシモーターなので、モーター出力ラインに、Common Modeフィルター、VDR(バリスタ―)、0.1μFの積層セラミックコンデンサーを追加しています。そしてDRV8835のIN1とIN2にPWMパルス信号を入力すれば、モーターが動きます。

使っている電源が異なるので、5.2Vと5.3Vと電圧も異なります。DRV8835のVM側は、11Vまで大丈夫なのですが、小さなモーターが5Vでした。VM側は、9V電池から少し容量の大きい3端子DC/DC5Vレギュレーター(NJM7805,～1.5Amax)で、5.3Vへ降圧しています。製作途中、モーターを基板に埋め込むのが、少し大変でした。今回使っているVDRバリスターは5年前に買ったリード線タイプですが、現在は販売終了しています。すべて面実装タイプになっているようです。写真で、モーターが回っているのでセイルが少しブレています。

※ DCモーターは、何回でも回る360度回転型のギヤ付ブラシモーターです。サーボ機能は付いていません。外観は似ていますが、180度回転型のサーボモーターではありません。以下のプログラムでは、ギヤモーターが何回転もします。

PWM周波数は、下表のように 2.25kHz です。この周波数は、可聴音域（20Hz～20kHz）の高音域です。モーターが回り始める0.5秒ほど前から、「キーン」という高音が、DCモーターから聞こえます。モーターのブラシ付近が、振動して音波を出しているのだと思います。普通のオーディオの大音量スピーカー配線に耳を当てても音は聞こえませんから。

一般にブラシモーターの電磁ノイズは、数MHz～数百MHzと言われているので、人間の耳では聞き取れません。コモンモードはノーマルモードとは異なりますが、数kHz～数百kHzのノイズ対策を想定しています（詳細は未確認）。

今回使っているコモンモードACM12VはTDK製です。メインの用途は、車載パワーラインのオルタネーターなどのフィルターのようです。DRV8835もそうですが、モバイルバッテリー用です。購入する時に見かけたページです。ご参考になれば。（外部：TDKのページ）
コンデンサの機能「共振回路と発振回路」
https://www.tdk.com/ja/tech-mag/condenser/004

この中で、アンテナがコンデンサーの開いたものであることを、初めて知りました。過去にも、地上波テレビアンテナで、放射アンテナの形状が、直線偏波・円偏波に影響があることを初めて知って、衝撃を受けたことがありましたが。

一方、今回のpwmの分解能(Resolution)は、10bitですから1024ステップです。ただしプログラム中では、下位1/4の256ステップしか使っていません。プラスチック歯車なので、フルパワーの最高速の回転にすると壊れるかもしれません。小さなモーターなので電流も1.5Amaxには達しないと思います。

RPI4B側のPythonプログラムは、初回と同じものを使います。

# RPI-0-uart-tx.py
# Serial Console OFF, Serial ON
# RPI4B Buster(x32) Python 3.7.3 (x32) Thonny, and RUN  or 
# RPI4B bookworm(x64) Python 3.11.2 Thonny, and RUN

import serial
#Open SERIALttyS0
SERIALttyS0 = serial.Serial('/dev/ttyS0', 2304000, timeout=1)
#Set SendMessage
SendMessage = "Hello PIC Im Pi.Hello PIC Im Pi."
#Send Command
SERIALttyS0.write(SendMessage.encode())
    
#Receive ReturnMessage and print
binary_ReturnMessage = SERIALttyS0.readline()
ReturnMessage = binary_ReturnMessage.decode()
print(ReturnMessage)
    
#Close SERIALttyS0
SERIALttyS0.close()

PIC側のプログラムは、mainの最下部のwhile内をDC-motor用に少し変えていますが、他は前回と全く同じです。今回も、xc8とC18のプログラムです。
PIC18FのXC8プログラムです。

//main.c    MPLAB  X IDE v6.00,  XC8 Compiler v2.4.0, (C90),  PICkit3
//pic18f2620 or 26k22
#include <xc.h>
#define _XTAL_FREQ 36864000
#define LED_A0		LATA0
#define lcd_B7		LATB7
#define lcd_B6		LATB6
#define lcd_B5		LATB5
#define lcd_B4		LATB4
#define lcd_stb_E	LATA1
#define lcd_rs		LATA2
#define SPIRAM1024_CS_TRIS		TRISC1
#define SPIRAM1024_CS_IO		LATC1
#define SPIRAM1024_SCK_TRIS		TRISC3
#define SPIRAM1024_SDI_TRIS		TRISC4
#define SPIRAM1024_SDO_TRIS		TRISC5
#define SPIRAM1024_SPI_IF 		SSPIF
#define SPIRAM1024_SSPBUF		SSPBUF
#define SPIRAM1024_SPICON1		SSPCON1
#define SPIRAM1024_SPICON1bits	SSPCON1bits
#define SPIRAM1024_SPICON2		SSPCON2
#define SPIRAM1024_SPISTAT		SSPSTAT
#define SPIRAM1024_SPISTATbits	SSPSTATbits 
#define FXMA_CS0_TRIS	TRISC0
#define FXMA_CS0_IO		LATC0

//2620
#pragma config OSC = HSPLL
#pragma config FCMEN = OFF
#pragma config IESO = OFF
#pragma config PWRT = ON
#pragma config BOREN = OFF
#pragma config BORV = 3
#pragma config WDT = OFF
#pragma config WDTPS = 32768
#pragma config CCP2MX = PORTBE
#pragma config PBADEN = OFF
#pragma config LPT1OSC = OFF
#pragma config MCLRE = ON
#pragma config STVREN = OFF
#pragma config LVP = OFF
#pragma config XINST = OFF
#pragma config CP0 = OFF
#pragma config CP1 = OFF
#pragma config CP2 = OFF
#pragma config CP3 = OFF
#pragma config CPB = OFF
#pragma config CPD = OFF
#pragma config WRT0 = OFF
#pragma config WRT1 = OFF
#pragma config WRT2 = OFF
#pragma config WRT3 = OFF
#pragma config WRTC = OFF
#pragma config WRTB = OFF
#pragma config WRTD = OFF
#pragma config EBTR0 = OFF
#pragma config EBTR1 = OFF
#pragma config EBTR2 = OFF
#pragma config EBTR3 = OFF
#pragma config EBTRB = OFF

////26k22
//#pragma config FOSC = HSHP
//#pragma config PLLCFG = ON
//#pragma config PRICLKEN = ON
//#pragma config FCMEN = OFF
//#pragma config IESO = OFF
//#pragma config PWRTEN = ON
//#pragma config BOREN = OFF
//#pragma config BORV = 190
//#pragma config WDTEN = OFF
//#pragma config WDTPS = 32768
//#pragma config CCP2MX = PORTC1
//#pragma config PBADEN = OFF
//#pragma config CCP3MX = PORTB5
//#pragma config HFOFST = OFF
//#pragma config T3CMX = PORTC0
//#pragma config P2BMX = PORTB5
//#pragma config MCLRE = EXTMCLR
//#pragma config STVREN = OFF
//#pragma config LVP = OFF
//#pragma config XINST = OFF
//#pragma config CP0 = OFF
//#pragma config CP1 = OFF
//#pragma config CP2 = OFF
//#pragma config CP3 = OFF
//#pragma config CPB = OFF
//#pragma config CPD = OFF
//#pragma config WRT0 = OFF
//#pragma config WRT1 = OFF
//#pragma config WRT2 = OFF
//#pragma config WRT3 = OFF
//#pragma config WRTC = OFF
//#pragma config WRTB = OFF
//#pragma config WRTD = OFF
//#pragma config EBTR0 = OFF
//#pragma config EBTR1 = OFF
//#pragma config EBTR2 = OFF
//#pragma config EBTR3 = OFF
//#pragma config EBTRB = OFF

static unsigned char vBANK01[256];
static unsigned char vBuffer[32];

near uint8_t i,j,k,p,q,r,s;
near unsigned char asci, cmd, data, data0, Temp1, Temp2;
near uint16_t Wi, Wi_last, num, Wj, Wk, Wp, Wq, Wr, Ws;
near uint32_t Di, Dj, Dk;

near uint32_t dAddress, dAddreNewHead, dLength, dTotalLengh;
near uint8_t Dummy, SPICON1Save;

////   lcd functions
void LCD__vBuffer32(void);
void LCD__Data(unsigned char data);
void LCD__Command(unsigned char cmd);
void LCD__Command_Upper(unsigned char cmd);
void LCD__Init(void);
void LCD__Clear(void);
void PUT_DATA(void);
void PUT_CMD(void);

////   SPIRAM1024 functions
void SPIRAM1024Init(void);
void SPIRAM1024GetArray(near uint32_t dAddress, near uint32_t dLength);
void SPIRAM1024PutArray(near uint32_t dAddress, near uint32_t dLength);


void main()
{
    //2620
    ADCON0 = 0x00;
    ADCON1 = 0x0F;

    ////26k22
    //ANSELA = 0b00100000 ;    // AN4(RA5)
    //ANSELB = 0b00000000 ;
    //ANSELC = 0b00000000 ;

    TRISA  = 0b00100000 ;    // RA5
    TRISB  = 0b00000000 ;
    TRISC  = 0b00000000 ;
    PORTA  = 0b00000000 ;
    PORTB  = 0b00000000 ;
    PORTC  = 0b00000000 ;

    TRISC = 0x90;
    TXSTA = 0x24;
    RCSTA = 0x90;
    BAUDCON = 0x00;	
    SPBRG = 0x00;

    // sram init
    #if defined(SPIRAM1024_CS_TRIS)                
        SPIRAM1024Init();                            
    #endif    

    // lcd init
    LCD__Init();
    LCD__Command(0x01);
    LCD__Command(0x0c);

    Temp1=0x30;    
    for(i = 0; i < 32; i++)        
    {
        vBANK01[i]=Temp1;
        Temp1++;
    }

    for(i = 0; i < 32; i++)
    {
        vBuffer[i]=vBANK01[i];    
    }
    LCD__vBuffer32();
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);

    SPIRAM1024PutArray(0,  32);

    for(i = 0; i < 32; i++)        
    {
        vBuffer[i]=0x30;
        vBANK01[i]=0x30;
    }
    LCD__vBuffer32();
    __delay_ms(1000);

    SPIRAM1024GetArray(0, 32);
    for(i = 0; i < 32; i++)        
    {
        vBuffer[i]=vBANK01[i];    
    }
    LCD__vBuffer32();
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);

    FXMA_CS0_TRIS =0;
    FXMA_CS0_IO=0;

    Wi=0;
    Wi_last=31;
    for(; ; )
    {
        if (RCSTAbits.OERR)
        {
            RCSTAbits.CREN = 0;
            Temp1 = RCREG;
            RCSTAbits.CREN = 1;
        }
        if(RCIF==1) 
        {
            vBANK01[Wi]  = RCREG;
            Wi++;
        }
        if(Wi>Wi_last) {  break;  }
    }

    vBuffer[0] =0x48;  // H
    vBuffer[1] =0x45;  // E
    vBuffer[2] =0x4C;  // L
    vBuffer[3] =0x4C;  // L
    vBuffer[4] =0x4F;  // O
    vBuffer[5] =0x20;  // 
    vBuffer[6] =0x50;  // P
    vBuffer[7] =0x69;  // i
    vBuffer[8] =0x20;  // 
    vBuffer[9] =0x49;  // I
    vBuffer[10]=0x6D;  // m
    vBuffer[11]=0x20;  // 
    vBuffer[12]=0x50;  // P
    vBuffer[13]=0x49;  // I
    vBuffer[14]=0x43;  // C
    vBuffer[15]=0x40;  // @
    vBuffer[16]=0x0A;  // LF

    Wi=0;
    Wi_last=17;
    for(; ; )
    {
        //2620
        if(TRMT==1)
        ////26k22
        //if(TXSTAbits.TRMT==1)
        {
            TXREG  =  vBuffer[Wi];
            Wi++;
        }
        if(Wi>Wi_last) {  break;  }
    }

    FXMA_CS0_IO=1;

    SPIRAM1024PutArray(0, 256);

    for(i = 0; i < 32; i++)        
    {
    	vBuffer[i]=0x30;
    	vBANK01[i]=0x30;
    }
    
    dAddreNewHead = 0;
    SPIRAM1024GetArray(dAddreNewHead, 32);
 
    for(i = 0; i < 32; i++)        
    {
    	vBuffer[i]=vBANK01[i];    
    }
    LCD__vBuffer32();
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);
    __delay_ms(250);
    
    //// 2620 pwm,  Standard CCP1 and CCP2(RB3) init
    CCP1CON  = 0b00001100 ;
    CCP2CON  = 0b00001100 ;
    T2CON	= 0b00000010 ;
    CCPR1L   = 0 ;
    CCPR1H   = 0 ;
    CCPR2L   = 0 ;
    CCPR2H   = 0 ;
    TMR2     = 0 ;
    PR2      = 249 ;
    T2CONbits.TMR2ON   = 1 ;

    ////// 26K22 pwm,  Standard CCP4 and CCP5 init
    //CCPTMRS1 = 0b00000100 ;
    //CCP4CON  = 0b00001100 ;
    //CCP5CON  = 0b00001100 ;
    //T2CON	= 0b00000010 ;
    //T4CON	= 0b00000010 ;
    //CCPR4L   = 0 ;
    //CCPR4H   = 0 ;
    //CCPR5L   = 0 ;
    //CCPR5H   = 0 ;
    //TMR2     = 0 ;
    //TMR4     = 0 ;
    //PR2      = 249 ;         // G-p182
    //PR4      = 249 ;         // G-p182
    //T2CONbits.TMR2ON   = 1 ;
    //T4CONbits.TMR4ON   = 1 ;

    while(1) {

        LED_A0 = 1;
        //////////  ClockWise / Acceleration   //////////
        for(Wi=0; Wi<=1023; Wi++)
        {
            ////2620
            CCPR1L = Wi/4 ;
            CCPR2L = 0 ;
            //////26k22
            //CCPR4L = Wi/4 ;
            //CCPR5L = 0 ;
            __delay_ms(2) ;
        }
        //////////  ClockWise / Deceleration   //////////
        for(Wi=0; Wi<=1023; Wi++)
        {
            ////2620
            CCPR1L = (1023-Wi)/4 ;
            CCPR2L = 0 ;
            //////26k22
            //CCPR4L = (1023-Wi)/4 ;
            //CCPR5L = 0 ;
            __delay_ms(2) ;
        }
        ///////////////   Breake    ////////////////////////
        //// 2620
        CCPR1L = 255 ;
        CCPR2L = 255 ;
        ////// 26k22
        //CCPR4L = 255 ;
        //CCPR5L = 255 ;
        __delay_ms(250) ;
        __delay_ms(250) ;
        __delay_ms(250) ;
        __delay_ms(250) ;

        LED_A0 = 0;
        //////////  Counter-ClockWise / Acceleration   //////////
        for(Wi=0; Wi<=1023; Wi++)
        {
            ////2620
            CCPR1L = 0 ;
            CCPR2L = Wi/4 ;
            //////26k22
            //CCPR4L = 0 ;
            //CCPR5L = Wi/4 ;
            __delay_ms(2) ;
        }
        //////////  Counter-ClockWise / Deceleration   //////////
        for(Wi=0; Wi<=1023; Wi++)
        {
            ////2620
            CCPR1L = 0 ;
            CCPR2L = (1023-Wi)/4 ;
            //////26k22
            //CCPR4L = 0 ;
            //CCPR5L = (1023-Wi)/4 ;
            __delay_ms(2) ;
        }
        ///////////////   Breake    ////////////////////////
        //// 2620
        CCPR1L = 255 ;
        CCPR2L = 255 ;
        ////// 26k22
        //CCPR4L = 255 ;
        //CCPR5L = 255 ;
        __delay_ms(250) ;
        __delay_ms(250) ;
        __delay_ms(250) ;
        __delay_ms(250) ;
     }
}


//  SC1602BS lcd functios  //
void LCD__vBuffer32(void)
{
	uint8_t ii;
	LCD__Clear();
	for(ii = 0; ii < 16; ii++){
		data= vBuffer[ii];
		LCD__Data(data);
	}
	LCD__Command(0xC0);
	for(ii = 16; ii < 32; ii++){
		data= vBuffer[ii];
		LCD__Data(data);
	}
}

void LCD__Data(unsigned char data)
{
	uint8_t jj;
	for(jj=0; jj<=1; jj++)
	{
		if (jj==0)
			data0=data;
		else
			data0=data<<4;
		lcd_B7 = 0;
		lcd_B6 = 0;
		lcd_B5 = 0;
		lcd_B4 = 0;
		if((data0 & 0x80) != 0)
			lcd_B7 = 1;
		if((data0 & 0x40) != 0)
			lcd_B6 = 1;
		if((data0 & 0x20) != 0)
			lcd_B5 = 1;
		if((data0 & 0x10) != 0)
			lcd_B4 = 1;
		PUT_DATA();
	}
	__delay_us(50);
}

void LCD__Command(unsigned char cmd)
{
	uint8_t jj;
	for(jj=0; jj<=1; jj++)
	{
		if (jj==0)
			data0=cmd;
		else
			data0=cmd<<4;
		lcd_B7 = 0;
		lcd_B6 = 0;
		lcd_B5 = 0;
		lcd_B4 = 0;
		if((data0 & 0x80) != 0)
			lcd_B7 = 1;
		if((data0 & 0x40) != 0)
			lcd_B6 = 1;
		if((data0 & 0x20) != 0)
			lcd_B5 = 1;
		if((data0 & 0x10) != 0)
			lcd_B4 = 1;
		PUT_CMD();
	}
	__delay_us(50);
}

void LCD__Command_Upper(unsigned char cmd)
{
	lcd_B7 = 0;
	lcd_B6 = 0;
	lcd_B5 = 0;
	lcd_B4 = 0;
	if((data0 & 0x80) != 0)
		lcd_B7 = 1;
	if((data0 & 0x40) != 0)
		lcd_B6 = 1;
	if((data0 & 0x20) != 0)
		lcd_B5 = 1;
	if((data0 & 0x10) != 0)
		lcd_B4 = 1;
	PUT_CMD();
	__delay_ms(5);
}

void LCD__Clear(void)
{
	LCD__Command(0x01);
	__delay_ms(250);
}

void LCD__Init(void)
{
	__delay_ms(50);
	LCD__Command_Upper(0x30);
	LCD__Command_Upper(0x30);
	LCD__Command_Upper(0x30);
	LCD__Command_Upper(0x20);
	LCD__Command(0x2E);
	LCD__Command(0x08);
	LCD__Command(0x0D);
	LCD__Command(0x06);
	LCD__Clear();
}

void PUT_CMD(void)
{
	lcd_rs  = 0;
	_delay(1);
	lcd_stb_E = 1;
	_delay(4);
	lcd_stb_E = 0;
}

void PUT_DATA(void)
{
	lcd_rs  = 1;
	_delay(1);
	lcd_stb_E = 1;
	_delay(4);
	lcd_stb_E = 0;
}


//// no-pointer spi-sram 23LC1024 functions,  referred from Microchip
// opcodes
#define READ	0x03			// Read data from memory array beginning at selected address
#define WRITE	0x02			// Write data to memory array beginning at selected address
#define RDSR	0x05			// Read Status register
#define WRSR	0x01			// Write Status register
// define
#define PROPER_SPICON1	(0x20)		// SSPEN bit is set, SPI in master mode, FOSC/4, IDLE state is low level

void SPIRAM1024Init(void)
{
	SPIRAM1024_CS_IO = 1;
	SPIRAM1024_CS_TRIS = 0;
	SPIRAM1024_SCK_TRIS = 0;
	SPIRAM1024_SDI_TRIS = 1;	
	SPIRAM1024_SDO_TRIS = 0;
	// Save SPI state (clock speed)
	SPICON1Save = SPIRAM1024_SPICON1;
	SPIRAM1024_SPICON1 = PROPER_SPICON1;
	SPIRAM1024_SPI_IF = 0;
	SPIRAM1024_SPISTATbits.CKE = 1; 
	SPIRAM1024_SPISTATbits.SMP = 0;
	// Set Burst mode
	// Activate chip select
	SPIRAM1024_CS_IO = 0;
	SPIRAM1024_SPI_IF = 0;
	// Send Write Status Register opcode
	SPIRAM1024_SSPBUF = WRSR;
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Set status register to 0b01000000 to enable burst mode
	SPIRAM1024_SSPBUF = 0x40;
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Deactivate chip select
	SPIRAM1024_CS_IO = 1;
	// Restore SPI state
	SPIRAM1024_SPICON1 = SPICON1Save;
}

void SPIRAM1024GetArray(near uint32_t dAddress, near uint32_t dLength)
{
	if(dLength == 0)
		return;
	// Save SPI state (clock speed)
	SPICON1Save = SPIRAM1024_SPICON1;
	SPIRAM1024_SPICON1 = PROPER_SPICON1;
	// Activate chip select
	SPIRAM1024_CS_IO = 0;
	SPIRAM1024_SPI_IF = 0;
	// Send READ opcode
	SPIRAM1024_SSPBUF = READ;
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Send address
	SPIRAM1024_SSPBUF = ((uint8_t*)&dAddress)[2];
	while(!SPIRAM1024_SPI_IF);	
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	//
	SPIRAM1024_SSPBUF = ((uint8_t*)&dAddress)[1];
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	//
	SPIRAM1024_SSPBUF = ((uint8_t*)&dAddress)[0];
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Read data
	for(Dk = 0; Dk < dLength; Dk++)
	{
		SPIRAM1024_SSPBUF = 0;
		while(!SPIRAM1024_SPI_IF);
		vBANK01[Dk] = SPIRAM1024_SSPBUF;
		SPIRAM1024_SPI_IF = 0;
	}
	// Deactivate chip select
	SPIRAM1024_CS_IO = 1;
	// Restore SPI state
	SPIRAM1024_SPICON1 = SPICON1Save;
}

void SPIRAM1024PutArray(near uint32_t dAddress, near uint32_t dLength)
{
	if(dLength == 0)
		return;
	// Save SPI state (clock speed)
	SPICON1Save = SPIRAM1024_SPICON1;
	SPIRAM1024_SPICON1 = PROPER_SPICON1;
	// Activate chip select
	SPIRAM1024_CS_IO = 0;
	SPIRAM1024_SPI_IF = 0;
	// Send WRITE opcode
	SPIRAM1024_SSPBUF = WRITE;
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Send address
	SPIRAM1024_SSPBUF = ((uint8_t*)&dAddress)[2];
	while(!SPIRAM1024_SPI_IF);	
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	//
	SPIRAM1024_SSPBUF = ((uint8_t*)&dAddress)[1];
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	//
	SPIRAM1024_SSPBUF = ((uint8_t*)&dAddress)[0];
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Write data
	for(Dk = 0; Dk < dLength; Dk++)
	{
		SPIRAM1024_SSPBUF = vBANK01[Dk];
		while(!SPIRAM1024_SPI_IF);
		Dummy = SPIRAM1024_SSPBUF;
		SPIRAM1024_SPI_IF = 0;
	}
	// Deactivate chip select
	SPIRAM1024_CS_IO = 1;
	// Restore SPI state
	SPIRAM1024_SPICON1 = SPICON1Save;
}

PIC18FのC18プログラムです。

// MainDemo.c     MPLAB_IDE_8_92,  MPLAB_C18_3.46,  PICkit3
#include <p18f2620.h>
//#include <p18f26k22.h>
#include <HardwareProfile.h>
#include <GenericTypeDefs.h>
#include <delays.h>

#pragma udata bank1  = 0x100
static unsigned char vBANK01[256];
#pragma udata bank2 = 0x200
static unsigned char vBuffer[32];

#pragma udata access my_access
near unsigned char asci, cmd, data, data0, Temp1, Temp2;
near BYTE i, j, k, ii, jj, kk;
near WORD Wi, Wi_last, num, Wj, Wk, Wp, Wq, Wr, Ws;
near DWORD Di, Dj, Dk;
near DWORD dAddress, dAddreNewHead, dLength, dTotalLengh;
near BYTE Dummy, SPICON1Save;

// LCD functions
void LCD__Data(void);
void LCD__vBuffer32(void);
void LCD__Command(void);
void LCD__Clear(void);
void LCD__Init(void);
void PUT_CMD(void);
void PUT_DATA(void);

// Time functions
void TIME50(void);
void TIME5M(void);

// SPI-SRAM1024 functions 
void SPIRAM1024Init(void);
void SPIRAM1024GetArray(near DWORD dAddress, near DWORD dLength);
void SPIRAM1024PutArray(near DWORD dAddress, near DWORD dLength);

#pragma code
void main(void){

	//2620
	ADCON0 = 0x00;
	ADCON1 = 0x0F;

	////26k22
	//ANSELA = 0b00100000 ;    // AN4(RA5)
	//ANSELB = 0b00000000 ;
	//ANSELC = 0b00000000 ;

	TRISA  = 0b00100000 ;    // RA5
	TRISB  = 0b00000000 ;
	TRISC  = 0b00000000 ;
	PORTA  = 0b00000000 ;
	PORTB  = 0b00000000 ;
	PORTC  = 0b00000000 ;

	TRISC = 0x90;
	TXSTA = 0x24;
	RCSTA = 0x90;
	BAUDCON = 0x00;	
	SPBRG = 0x00;

	LCD__Init();

	#if defined(SPIRAM1024_CS_TRIS)				
		SPIRAM1024Init();							
	#endif																		

	Temp1=0x41;	
	for(i = 0; i < 32; i++)		
	{
		vBANK01[i]=Temp1;	
		_asm  INCF  Temp1, 1, 0  _endasm
	}
	for(i = 0; i < 32; i++)
	{
		vBuffer[i]=vBANK01[i];	
	}
	LCD__vBuffer32();
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);

	SPIRAM1024PutArray(0,  32);	    // SRAM Write

	for(i = 0; i < 32; i++)	    	   // clear buffer
	{
		vBuffer[i]=0x30;
		vBANK01[i]=0x30;
	}
	LCD__vBuffer32();
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);

	SPIRAM1024GetArray(0, 32);	    // SRAM Read	
	for(i = 0; i < 32; i++)		
	{
		vBuffer[i]=vBANK01[i];	
	}
	LCD__vBuffer32();
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);

	LED0_IO = 0;

	FXMA_CS0_TRIS = 0;
	FXMA_CS0_IO = 0;

	for(Wi = 0; Wi < 32; Wi++)
	{
		if (RCSTAbits.OERR) 
		{
			RCSTAbits.CREN = 0;
			Temp1 = RCREG;
			RCSTAbits.CREN = 1;
		}
		_asm BTFSS  PIR1, 5, 0 _endasm      // RCIF in P1R1 = 5
		_asm BRA -2	           _endasm
		vBANK01[Wi]  = RCREG;
	}

	vBuffer[0] =0x48;  // H
	vBuffer[1] =0x45;  // E
	vBuffer[2] =0x4C;  // L
	vBuffer[3] =0x4C;  // L
	vBuffer[4] =0x4F;  // O
	vBuffer[5] =0x20;  // 
	vBuffer[6] =0x50;  // P
	vBuffer[7] =0x69;  // i
	vBuffer[8] =0x20;  // 
	vBuffer[9] =0x49;  // I
	vBuffer[10]=0x6D;  // m
	vBuffer[11]=0x20;  // 
	vBuffer[12]=0x50;  // P
	vBuffer[13]=0x49;  // I
	vBuffer[14]=0x43;  // C
	vBuffer[15]=0x40;  // @
	vBuffer[16]=0x0A;  // LF

	for(i = 0; i < 18; i++)		
	{
		_asm BTFSS TXSTA, 1, 0 _endasm      // TRMT in TXSTA = 1
		_asm BRA   -2	       _endasm
		TXREG  =  vBuffer[i];
	}

	FXMA_CS0_IO = 1;

	SPIRAM1024PutArray(0, 256);       // SRAM Write

	for(i = 0; i < 32; i++)		
	{
		vBuffer[i]=0x30;
		vBANK01[i]=0x30;
	}
	
	dAddreNewHead = 0;
	SPIRAM1024GetArray(dAddreNewHead, 32);    // SRAM Read

	for(i = 0; i < 32; i++)		
	{
		vBuffer[i]=vBANK01[i];	
	}
	LCD__vBuffer32();
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);
	Delay10KTCYx(250);

	//// 2620 pwm,  Standard CCP1 and CCP2(RB3) init
	CCP1CON  = 0b00001100 ;
	CCP2CON  = 0b00001100 ;
	T2CON	= 0b00000010 ;
	CCPR1L   = 0 ;
	CCPR1H   = 0 ;
	CCPR2L   = 0 ;
	CCPR2H   = 0 ;
	TMR2	 = 0 ;
	PR2	  = 249 ;
	T2CONbits.TMR2ON   = 1 ;

	////// 26K22 pwm,  Standard CCP4 and CCP5 init
	//CCPTMRS1 = 0b00000100 ;
	//CCP4CON  = 0b00001100 ;
	//CCP5CON  = 0b00001100 ;
	//T2CON	= 0b00000010 ;
	//T4CON	= 0b00000010 ;
	//CCPR4L   = 0 ;
	//CCPR4H   = 0 ;
	//CCPR5L   = 0 ;
	//CCPR5H   = 0 ;
	//TMR2	 = 0 ;
	//TMR4	 = 0 ;
	//PR2	  = 249 ;		 // G-p182
	//PR4	  = 249 ;		 // G-p182
	//T2CONbits.TMR2ON   = 1 ;
	//T4CONbits.TMR4ON   = 1 ;

	while(1)
	{
		LED0_IO = 1;
		////////// ClockWise / Acceleration  //////////
		for(Wi=0; Wi<=1023; Wi++)
		{
			////2620
			CCPR1L = Wi/4 ;
			CCPR2L = 0 ;
			//////26k22
			//CCPR4L = Wi/4 ;
			//CCPR5L = 0 ;
			Delay10KTCYx(2) ;
		}
		////////// ClockWise / Deceleration  //////////
		for(Wi=0; Wi<=1023; Wi++)
		{
			////2620
			CCPR1L = (1023-Wi)/4 ;
			CCPR2L = 0 ;
			//////26k22
			//CCPR4L = (1023-Wi)/4 ;
			//CCPR5L = 0 ;
			Delay10KTCYx(2) ;
		}
		///////////////   Breake	////////////////////////
		//// 2620
		CCPR1L = 255 ;
		CCPR2L = 255 ;
		////// 26k22
		//CCPR4L = 255 ;
		//CCPR5L = 255 ;
		Delay10KTCYx(250) ;
		Delay10KTCYx(250) ;
		Delay10KTCYx(250) ;
		Delay10KTCYx(250) ;

		LED0_IO = 0;
		//////////  Counter-ClockWise / Acceleration  //////////
		for(Wi=0; Wi<=1023; Wi++)
		{
			////2620
			CCPR1L = 0 ;
			CCPR2L = Wi/4 ;
			//////26k22
			//CCPR4L = 0 ;
			//CCPR5L = Wi/4 ;
			Delay10KTCYx(2) ;
		}
		//////////   Counter-ClockWise / Deceleration  //////////
		for(Wi=0; Wi<=1023; Wi++)
		{
			////2620
			CCPR1L = 0 ;
			CCPR2L = (1023-Wi)/4 ;
			//////26k22
			//CCPR4L = 0 ;
			//CCPR5L = (1023-Wi)/4 ;
			Delay10KTCYx(2) ;
		}
		///////////////   Breake	////////////////////////
		//// 2620
		CCPR1L = 255 ;
		CCPR2L = 255 ;
		////// 26k22
		//CCPR4L = 255 ;
		//CCPR5L = 255 ;
		Delay10KTCYx(250) ;
		Delay10KTCYx(250) ;
		Delay10KTCYx(250) ;
		Delay10KTCYx(250) ;
	}	
}

#pragma tmpdata

//// lcd functions
void LCD__Data(void)
{
	_asm MOVWF Temp1, 0 	_endasm
	_asm MOVLW 0x0F 		_endasm
	_asm ANDWF PORTB, 1, 0 	_endasm
	_asm MOVF  Temp1, 0, 0 	_endasm
	_asm ANDLW 0xF0 		_endasm
	_asm IORWF PORTB, 1, 0 	_endasm
	PUT_DATA();
	_asm MOVLW 0x0F 		_endasm
	_asm ANDWF PORTB, 1, 0 	_endasm
	_asm SWAPF Temp1, 0, 0  _endasm
	_asm ANDLW 0xF0 		_endasm
	_asm IORWF PORTB, 1, 0 	_endasm
	PUT_DATA();
	TIME50();
}

void LCD__vBuffer32(void)
{
	LCD__Clear();
	for(kk = 0; kk < 16; kk++)		
	{
		Temp1= vBuffer[kk];
		LCD__Data();
	}
	_asm MOVLW 0xC0  	_endasm	
	LCD__Command();			
	TIME50();
	for(kk = 16; kk < 32; kk++)		
	{
		Temp1= vBuffer[kk];
		LCD__Data();
	}
}

void PUT_CMD(void)
{	
	lcd_rs  = 0;
	Nop();
	lcd_stb = 1;
	Nop();				
	Nop();
	Nop();				
	Nop();	
	lcd_stb = 0;
}

void PUT_DATA(void)
{
	lcd_rs  = 1;
	Nop();
	lcd_stb = 1;
	Nop();				
	Nop();
	Nop();				
	Nop();	
	lcd_stb = 0;
}

void LCD__Command(void)
{							
	_asm MOVWF Temp1, 0 	_endasm		
	_asm MOVLW 0x0F 		_endasm		
	_asm ANDWF PORTB, 1, 0 	_endasm		
	_asm MOVF  Temp1, 0, 0 	_endasm		
	_asm ANDLW 0xF0 		_endasm		
	_asm IORWF PORTB, 1, 0 	_endasm		
	PUT_CMD();
	_asm MOVLW 0x0F 		_endasm
	_asm ANDWF PORTB, 1, 0 	_endasm		
	_asm SWAPF Temp1, 0, 0  _endasm		
	_asm ANDLW 0xF0 		_endasm
	_asm IORWF PORTB, 1, 0 	_endasm		
	PUT_CMD();
	TIME50();				
}

void LCD__Clear(void)
{
	_asm MOVLW 0x01  	_endasm
	LCD__Command();	
	Delay10KTCYx(125);
	Delay10KTCYx(125);
}

void LCD__Init(void)
{	
	TIME5M();
	TIME5M();
	TIME5M();
	TIME5M();
	TIME5M();
	TIME5M();
	TIME5M();
	_asm MOVLW	0x0F	 		_endasm
	_asm ANDWF	PORTB,    1, 0 	_endasm
	_asm MOVLW	0x30			_endasm
	_asm IORWF	PORTB,    1, 0 	_endasm
	PUT_CMD();
	TIME5M();
	PUT_CMD();
	TIME5M();
	PUT_CMD();
	TIME5M();
	_asm MOVLW	0x0F	 		_endasm
	_asm ANDWF	PORTB,    1, 0 	_endasm	
	_asm MOVLW	0x20	 		_endasm
	_asm IORWF	PORTB,    1, 0 	_endasm
	PUT_CMD();
	TIME5M();
	_asm MOVLW 0x2E  		_endasm	
	LCD__Command();	
	_asm MOVLW 0x08 		_endasm
	LCD__Command();	
	_asm MOVLW 0x0D  		_endasm
	LCD__Command();	
	_asm MOVLW 0x06  		_endasm
	LCD__Command();	
	LCD__Clear();
}

//  about 50usec at 40MHz
void TIME50(void)
{
	_asm MOVLW	0x63		_endasm
	_asm MOVWF	ii, 0		_endasm 
	_asm NOP				_endasm
	_asm NOP				_endasm
	_asm DECFSZ	ii, 1, 0	_endasm	
	_asm BRA	-4			_endasm
}

//  about 5msec at 40MHz
void TIME5M(void)
{
	_asm MOVLW	0x64		_endasm
	_asm MOVWF	jj, 0		_endasm
	TIME50();
	_asm DECFSZ	jj, 1, 0	_endasm
	_asm BRA	-3			_endasm
}


//// no-pointer spi-sram (23LC1024) functions : referred from Microchip
// opcodes
#define READ	0x03			// Read data from memory array beginning at selected address
#define WRITE	0x02			// Write data to memory array beginning at selected address
#define RDSR	0x05			// Read Status register
#define WRSR	0x01			// Write Status register
// define
#define PROPER_SPICON1	(0x20)	// SSPEN bit is set, SPI in master mode, FOSC/4, IDLE state is low level

void SPIRAM1024Init(void)
{
	SPIRAM1024_CS_IO = 1;
	SPIRAM1024_CS_TRIS = 0;
	SPIRAM1024_SCK_TRIS = 0;			// SCK pin    output
	SPIRAM1024_SDI_TRIS = 1;			// SDI pin    input
	SPIRAM1024_SDO_TRIS = 0;			// SDO pin    output
	// Save SPI state (clock speed)
	SPICON1Save = SPIRAM1024_SPICON1;
	SPIRAM1024_SPICON1 = PROPER_SPICON1;
	SPIRAM1024_SPI_IF = 0;
	SPIRAM1024_SPISTATbits.CKE = 1; 	// Transmit data on rising edge of clock
	SPIRAM1024_SPISTATbits.SMP = 0;		// Input sampled at middle of data output time
	// Set Burst mode
	// Activate chip select
	SPIRAM1024_CS_IO = 0;
	SPIRAM1024_SPI_IF = 0;
	// Send Write Status Register opcode
	SPIRAM1024_SSPBUF = WRSR;
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Set status register to 0b01000000 to enable burst mode
	SPIRAM1024_SSPBUF = 0x40;
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Deactivate chip select
	SPIRAM1024_CS_IO = 1;
	// Restore SPI state
	SPIRAM1024_SPICON1 = SPICON1Save;
}

void SPIRAM1024GetArray(near DWORD dAddress, near DWORD dLength)
{
	// Ignore operations when the destination is NULL or nothing to read
	if(vBANK01 == NULL)
		return;
	if(dLength == 0)
		return;
	// Save SPI state (clock speed)
	SPICON1Save = SPIRAM1024_SPICON1;
	SPIRAM1024_SPICON1 = PROPER_SPICON1;
	// Activate chip select
	SPIRAM1024_CS_IO = 0;
	SPIRAM1024_SPI_IF = 0;
	// Send READ opcode
	SPIRAM1024_SSPBUF = READ;
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Send address
	SPIRAM1024_SSPBUF = ((BYTE*)&dAddress)[2];
	while(!SPIRAM1024_SPI_IF);	
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	//
	SPIRAM1024_SSPBUF = ((BYTE*)&dAddress)[1];
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	//
	SPIRAM1024_SSPBUF = ((BYTE*)&dAddress)[0];
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Read data
	for(Dk = 0; Dk < dLength; Dk++)
	{
		SPIRAM1024_SSPBUF = 0;
		while(!SPIRAM1024_SPI_IF);
		vBANK01[Dk] = SPIRAM1024_SSPBUF;
		SPIRAM1024_SPI_IF = 0;
	}
	// Deactivate chip select
	SPIRAM1024_CS_IO = 1;
	// Restore SPI state
	SPIRAM1024_SPICON1 = SPICON1Save;
}

void SPIRAM1024PutArray(near DWORD dAddress, near DWORD dLength)
{
	// Ignore operations when the source data is NULL
	if(vBANK01 == NULL)
		return;
	if(dLength == 0)
		return;
	// Save SPI state (clock speed)
	SPICON1Save = SPIRAM1024_SPICON1;
	SPIRAM1024_SPICON1 = PROPER_SPICON1;
	// Activate chip select
	SPIRAM1024_CS_IO = 0;
	SPIRAM1024_SPI_IF = 0;
	// Send WRITE opcode
	SPIRAM1024_SSPBUF = WRITE;
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Send address
	////
	SPIRAM1024_SSPBUF = ((BYTE*)&dAddress)[2];
	while(!SPIRAM1024_SPI_IF);	
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	////
	SPIRAM1024_SSPBUF = ((BYTE*)&dAddress)[1];
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	////
	SPIRAM1024_SSPBUF = ((BYTE*)&dAddress)[0];
	while(!SPIRAM1024_SPI_IF);
	Dummy = SPIRAM1024_SSPBUF;
	SPIRAM1024_SPI_IF = 0;
	// Write data
	for(Dk = 0; Dk < dLength; Dk++)
	{
		SPIRAM1024_SSPBUF = vBANK01[Dk];
		while(!SPIRAM1024_SPI_IF);
		Dummy = SPIRAM1024_SSPBUF;
		SPIRAM1024_SPI_IF = 0;
	}
	// Deactivate chip select
	SPIRAM1024_CS_IO = 1;
	// Restore SPI state
	SPIRAM1024_SPICON1 = SPICON1Save;
}

C18用のHardwareProfile.hとConfiguration Bitsは、前々回と同じです。

次回はPIC側で、温度センサーMCP9700の電圧を、PICのA／Dコンバーターを使って、表示します。