LoginSignup
1
0

More than 5 years have passed since last update.

@masashi_214

NMRA DCC Function Decoder スケッチ

Posted at

概要

NMRA DCCライブラリを使用したFunction Decodetスケッチです

動作

・DCC信号を受信するけどなにもしません

// DCC Function Decoder Base Rev 1.0 for Smile Function Decoder
// http://dcc.client.jp
// http://ayabu.blog.shinobi.jp
//
// O1:F3 でON/OFF head sign
// O2:F0 でON/OFF head light
// O3:F1 でON/OFF tail light
// O4:F5 でON/OFF room light

#include "NmraDcc.h"
#include <avr/eeprom.h>  //required by notifyCVRead() function if enabled below

//各種設定、宣言
#define DECODER_ADDRESS 3
#define DCC_ACK_PIN 0   // Atiny85 PB0(5pin) if defined enables the ACK pin functionality. Comment out to disable.
//                      // Atiny85 DCCin(7pin)
#define O1 0            // Atiny85 PB0(5pin)             head sign light
#define O2 1            // Atiny85 PB1(6pin) analogwrite Head light
#define O3 3            // Atint85 PB3(2pin)             tail light
#define O4 4            // Atiny85 PB4(3pin) analogwrite room light

#define MAX_PWMDUTY 255
#define MID_PWMDUTY 10

#define CV_VSTART       2
#define CV_ACCRATIO     3
#define CV_DECCRATIO    4
#define CV_F0_FORWARD 33
#define CV_F0_BACK 34
#define CV_F1 35
#define CV_F2 36
#define CV_F3 37
#define CV_F4 38
#define CV_F5 39
#define CV_F6 40
#define CV_F7 41
#define CV_F8 42
#define CV_F9 43
#define CV_F10 44
#define CV_F11 45
#define CV_F12 46

//ファンクションの変数
uint8_t fn_bit_f0 = 0;
uint8_t fn_bit_f1 = 0;
uint8_t fn_bit_f2 = 0;
uint8_t fn_bit_f3 = 0;
uint8_t fn_bit_f4 = 0;
uint8_t fn_bit_f5 = 0;
uint8_t fn_bit_f6 = 0;
uint8_t fn_bit_f7 = 0;
uint8_t fn_bit_f8 = 0;
uint8_t fn_bit_f9 = 0;
uint8_t fn_bit_f10 = 0;
uint8_t fn_bit_f11 = 0;
uint8_t fn_bit_f12 = 0;
uint8_t fn_bit_f13 = 0;
uint8_t fn_bit_f14 = 0;
uint8_t fn_bit_f15 = 0;
uint8_t fn_bit_f16 = 0;
uint8_t fn_bit_f17 = 0;
uint8_t fn_bit_f18 = 0;
uint8_t fn_bit_f19 = 0;
uint8_t fn_bit_f20 = 0;
uint8_t fn_bit_f21 = 0;
uint8_t fn_bit_f22 = 0;
uint8_t fn_bit_f23 = 0;
uint8_t fn_bit_f24 = 0;
uint8_t fn_bit_f25 = 0;
uint8_t fn_bit_f26 = 0;
uint8_t fn_bit_f27 = 0;
uint8_t fn_bit_f28 = 0;

//使用クラスの宣言
NmraDcc  Dcc;
DCC_MSG  Packet;

//Task Schedule (gはglobal)
unsigned long gPreviousL5 = 0;

//進行方向
uint8_t gDirection = 128;

//Function State
uint8_t gState_F0 = 0;
uint8_t gState_F1 = 0;
uint8_t gState_F2 = 0;
uint8_t gState_F3 = 0;
uint8_t gState_F4 = 0;
uint8_t gState_F5 = 0;
uint8_t gState_F6 = 0;
uint8_t gState_F7 = 0;
uint8_t gState_F8 = 0;
uint8_t gState_F9 = 0;
uint8_t gState_F10 = 0;
uint8_t gState_F11 = 0; 
uint8_t gState_F12 = 0;

//モータ制御関連の変数
uint32_t gSpeedRef = 1;

//CV related
uint8_t gCV1_SAddr = 3; 
uint8_t gCVx_LAddr = 3;
uint8_t gCV49_fx = 20;
uint8_t gCV50_DimmingSpeed = 1;
uint8_t gCV51_DimmingLightQuantity = 10;
uint8_t gCV52_RoomDimming = 128;

//Internal variables and other.
#if defined(DCC_ACK_PIN)
const int DccAckPin = DCC_ACK_PIN ;
#endif

struct CVPair {
  uint16_t  CV;
  uint8_t   Value;
};
CVPair FactoryDefaultCVs [] = {
  {CV_MULTIFUNCTION_PRIMARY_ADDRESS, DECODER_ADDRESS}, // CV01
  {CV_ACCESSORY_DECODER_ADDRESS_MSB, 0},               // CV09 The LSB is set CV 1 in the libraries .h file, which is the regular address location, so by setting the MSB to 0 we tell the library to use the same address as the primary address. 0 DECODER_ADDRESS
  {CV_MULTIFUNCTION_EXTENDED_ADDRESS_MSB, 0},          // CV17 XX in the XXYY address
  {CV_MULTIFUNCTION_EXTENDED_ADDRESS_LSB, 0},          // CV18 YY in the XXYY address
  {CV_29_CONFIG, 128 },                                // CV29 Make sure this is 0 or else it will be random based on what is in the eeprom which could caue headaches
};

void(* resetFunc) (void) = 0;  //declare reset function at address 0
void LightMes( char,char );
void pulse(void);

uint8_t FactoryDefaultCVIndex = sizeof(FactoryDefaultCVs) / sizeof(CVPair);

void notifyDccReset(uint8_t hardReset );

//uint16_t limitSpeed(uint16_t inSpeed);

void notifyCVResetFactoryDefault()
{
  //When anything is writen to CV8 reset to defaults.

  resetCVToDefault();
  //Serial.println("Resetting...");
  delay(1000);  //typical CV programming sends the same command multiple times - specially since we dont ACK. so ignore them by delaying

  resetFunc();
};

//------------------------------------------------------------------
// リセット処理
//------------------------------------------------------------------
void notifyDccReset(uint8_t hardReset )
{
  digitalWrite(O1,LOW);
  digitalWrite(O2,LOW);
  digitalWrite(O3,LOW);
  digitalWrite(O4,LOW);
}

//------------------------------------------------------------------
// CVをデフォルトにリセット
// Serial.println("CVs being reset to factory defaults");
//------------------------------------------------------------------
void resetCVToDefault()
{
  for (int j = 0; j < FactoryDefaultCVIndex; j++ ) {
    Dcc.setCV( FactoryDefaultCVs[j].CV, FactoryDefaultCVs[j].Value);
  }
};



extern void    notifyCVChange( uint16_t CV, uint8_t Value) {
  //CVが変更されたときのメッセージ
  //Serial.print("CV ");
  //Serial.print(CV);
  //Serial.print(" Changed to ");
  //Serial.println(Value, DEC);
};

//------------------------------------------------------------------
// CV Ack
//------------------------------------------------------------------
void notifyCVAck(void)
{
  //Serial.println("notifyCVAck");
  digitalWrite(O1,HIGH);
  digitalWrite(O2,HIGH);
  digitalWrite(O3,HIGH);
  digitalWrite(O4,HIGH);

  delay( 6 );

  digitalWrite(O1,LOW);
  digitalWrite(O2,LOW);
  digitalWrite(O3,LOW);
  digitalWrite(O4,LOW);
}

//------------------------------------------------------------------
// Arduino固有の関数 setup() :初期設定
//------------------------------------------------------------------
void setup()
{
// TCCR1:タイマ/カウンタ1制御レジスタ (Timer/Counter0 Control Register)
//        CTC1 | PWM1A | COM1A1 | COM1A0 | CS13 | CS12 | CS11 | CS10
// CS10等はiotnx5.hで定義されています。#define CTC1 7
// 1<<CS10 だと CPU CLKそのまま
  TCCR1 = 0<<CTC1 | 0<<PWM1A | 0<<COM1A0 | 1<<CS10;

  pinMode(O1, OUTPUT);
  pinMode(O2, OUTPUT);
  pinMode(O3, OUTPUT);
  pinMode(O4, OUTPUT);

  //DCCの応答用負荷ピン
#if defined(DCCACKPIN)
  //Setup ACK Pin
  pinMode(DccAckPin, OUTPUT);
  digitalWrite(DccAckPin, 0);
#endif

#if !defined(DECODER_DONT_DEFAULT_CV_ON_POWERUP)
  if ( Dcc.getCV(CV_MULTIFUNCTION_PRIMARY_ADDRESS) == 0xFF ) {   //if eeprom has 0xFF then assume it needs to be programmed
    //Serial.println("CV Defaulting due to blank eeprom");
    notifyCVResetFactoryDefault();

  } else {
    //Serial.println("CV Not Defaulting");
  }
#else
  //Serial.println("CV Defaulting Always On Powerup");
  notifyCVResetFactoryDefault();
#endif

  // Setup which External Interrupt, the Pin it's associated with that we're using, disable pullup.
  Dcc.pin(0, 2, 0); // Atiny85 7pin(PB2)をDCC_PULSE端子に設定

  // Call the main DCC Init function to enable the DCC Receiver
  Dcc.init( MAN_ID_DIY, 100,   FLAGS_MY_ADDRESS_ONLY , 0 );

  //Reset task
  gPreviousL5 = millis();

  //Init CVs
  gCV1_SAddr = Dcc.getCV( CV_MULTIFUNCTION_PRIMARY_ADDRESS ) ;
}

//---------------------------------------------------------------------
// Arduino main loop
//---------------------------------------------------------------------
void loop() {
  // You MUST call the NmraDcc.process() method frequently from the Arduino loop() function for correct library operation
  Dcc.process();

  if ( (millis() - gPreviousL5) >= 10) // 100:100msec  10:10msec  Function decoder は 10msecにしてみる。
  {
    //Reset task
    gPreviousL5 = millis();
  }
}

//---------------------------------------------------------------------
// DCC速度信号の受信によるイベント
//---------------------------------------------------------------------
extern void notifyDccSpeed( uint16_t Addr, DCC_ADDR_TYPE AddrType, uint8_t Speed, DCC_DIRECTION Dir, DCC_SPEED_STEPS SpeedSteps )
{
  if ( gDirection != Dir )
  {
    gDirection = Dir;
  }
  gSpeedRef = Speed;
}

//---------------------------------------------------------------------------
//ファンクション信号受信のイベント
//FN_0_4とFN_5_8は常時イベント発生（DCS50KはF8まで）
//FN_9_12以降はFUNCTIONボタンが押されたときにイベント発生
//前値と比較して変化あったら処理するような作り。
//---------------------------------------------------------------------------
//extern void notifyDccFunc( uint16_t Addr, FN_GROUP FuncGrp, uint8_t FuncState)
extern void notifyDccFunc(uint16_t Addr, DCC_ADDR_TYPE AddrType, FN_GROUP FuncGrp, uint8_t FuncState)
{

  if( FuncGrp == FN_0_4)
  {
    if( gState_F0 != (FuncState & FN_BIT_00))
    {
      //Get Function 0 (FL) state
      gState_F0 = (FuncState & FN_BIT_00);
    }
    if( gState_F1 != (FuncState & FN_BIT_01))
    {
      //Get Function 1 state
      gState_F1 = (FuncState & FN_BIT_01);
    }
    if( gState_F2 != (FuncState & FN_BIT_02))
    {
      gState_F2 = (FuncState & FN_BIT_02);
    }
    if( gState_F3 != (FuncState & FN_BIT_03))
    {
      gState_F3 = (FuncState & FN_BIT_03);
    }
    if( gState_F4 != (FuncState & FN_BIT_04))
    {
      gState_F4 = (FuncState & FN_BIT_04);
    }
  }

  if( FuncGrp == FN_5_8)
  {
    if( gState_F5 != (FuncState & FN_BIT_05))
    {
      //Get Function 0 (FL) state
      gState_F5 = (FuncState & FN_BIT_05);
    }
    if( gState_F6 != (FuncState & FN_BIT_06))
    {
      //Get Function 1 state
      gState_F6 = (FuncState & FN_BIT_06);
    }
    if( gState_F7 != (FuncState & FN_BIT_07))
    {
      gState_F7 = (FuncState & FN_BIT_07);
    }
    if( gState_F8 != (FuncState & FN_BIT_08))
    {
      gState_F8 = (FuncState & FN_BIT_08);
    }
  }
}
1
0
0

Register as a new user and use Qiita more conveniently

  1. You get articles that match your needs
  2. You can efficiently read back useful information
  3. You can use dark theme
What you can do with signing up
Sign upLogin
1
0