概要
TryHackMe「Physical Security Intro」のWalkthroughです。
Task2
Q1.Using an angle grinder to cut a lock open is what type of entry?
A.1
Q2.Lock picking could be considered what type of entry?
A.2
Q3.Lock bypassing can be considered what type of entry?
A.2
Q4.Taking a photo of a key, decoding it and duplicating it can be considered what type of entry?
A.3
Q5.Determining the combination of a safe through surveillance can be considered what type of entry?
A.3
Q6.Breaking a window to gain entry can be considered what type of entry?
A.1
Task3
Q1.What is the name of the tool which is used to apply torque to the core of a lock when picking?
A.Tension Wrench
Q2.What is the term used for picking a single pin at a time?
A.Single Pin Picking
Q3.What is the abbreviation commonly used to reference the above answer?
A.SPP
Q4.What is the term used when you try to randomly set pins?
A.Raking
Q5.This type of lock is typically cheap, low quality, and found on low security applications such as office desk cabinets.
A.Wafer Lock
Q6.This type of pick profile is usually used when single pin picking.
A.Hook
Q7.When single pin picking, this term refers to when you feel like you have set a pin and the core rotates slightly
A.False Set
Q8.This type of security driver pin gives several clicks as it is being picked.
A.Serrated
Task4
Q1.What is the interface between the two pins in a pin stack referred to as?
A.Shear Line
Q2.What are the pins on the bottom half of a pin stack referred to as? (you don't have to enter the word pin in the answer)
A.Key
Q3.What are the pins on the top half of a pin stack referred to as? (you don't have to enter the word pin in the answer)
A.Driver
Q4.What non-shimmable elements do padlocks use to keep the shackle in place?
A.Ball Bearings
Q5.What is the piece that allows locking lugs to retract when the core is turned?
A.Actuator
Q6.What piece of a standard door latch should remain completely depressed when the door is closed to prevent loiding/slipping of the latch?
A.Dead latch
Q7.What is the locking mechanism that has a bolt which protrudes into the frame of the door preventing it from opening?
A.Deadbolt
Task5
Q1.A lock which is unshielded is susceptible to what bypass tool?
A.Knife
Q2.A lock which has spring loaded locking lugs rather than ball bearings can be bypassed with what tool?
A.Shim
Q3.Combination locks such as the Masterlock 5400D are susceptible to a bypass which reveals the combination What is this method known as?
A.Decoding
Q4.The Masterlock 175 is infamous for its ability to be bypassed using what type of bypass?
A.Mini Knife
Q5.What bypass method uses a key cut to the lowest depths and kinetic energy to bounce the driver pins above the shear line and allow a lock to be opened?
A.Bumping
Q6.Locks which have spring loaded locking lugs can be opened by tapping a hammer on the side of the lock. What is this attack method called?
A.Rapping
Q7.What type of pick takes advantage of lazy manufacturing practices by lifting all the key pins and driver pins above the shear line to bypass a lock?
A.Comb
Q8.What tools can be wiggled inside the keyway of wafer locks to roughly simulate the biting of the key and open the lock?
A.Jiggler
Task6
Q1.What tool is used to reach under a door and actuate a handle from the interior?
A.Under The Door Tool
Q2.What tool can be used to bypass a set of double doors which have a crash bar on the secure side?
A.Double Door Tool
Q3.What item can be used to widen the gaps between doors and door frames or between double doors to allow for other bypass tools to be used? This tool is also common for automobile entry.
A.Air Wedge
Q4.An improperly hung door which opens away from you can be bypassed using this type of tool?
A.Shim
Q5.An improperly hung door which opens away from you can be bypassed using this type of tool?
A.traveler hook
Q6.What type of material can be used to go over the door to grab the secure side handles when an under the door tool is not able to be used?
A.Film
Q7.Canned air can be used to bypass what type of door controller hardware?
A.REX sensor
Q8.Adams Rite hardware fixtures are susceptible to a bypass where a wire is snaked through the keyway and actuates the locking mechanism behind it, what could prevent this bypass?
A.shielding