Specification of Communication Manager, No.79, 2021-11
AUTOSAR R21-11記事一覧はこちら。
AUTOSAR 21-11, 200文書読んだ。2022年5月に全部到達。
AUTOSAR R21-11(0) 仕様ダウンロード一覧。単語帳。参考文献資料作成
用語(terms)
| Term | Description |
|---|---|
| BSW | Basic Software |
| BswM | Basic Software Mode Manager |
| ComM | Communication Manager |
| DCM | Diagnostic Communication Manager |
| Det | Default Error Tracer |
| EcuM | ECU State Manager module |
| I-PDU | Information Protocol Data Unit |
| NM | Network Management |
| PDU | Protocol Data Unit |
| SW-C | Software Component |
| VMM | Vehicle Message Matrix |
| OA TC10 | Open Alliance TC10 specification (see [33]) |
| IRA | Internal Request Array. This is a bit vector which contains the aggregated internal PNC requests per channel. (see also chapter 8.6.2 “Nm_UpdateIRA”) |
| EIRA | External and Internal Request Array. This is a bit vector which contains the aggregated external and internal PNC requests |
| ERA | External Request Array. This is a bit vector which contains the aggregated external PNC requests. Each ComMChannel which has a ComMGatewayType set is has one corresponding ERA |
| ERAn | All External Request Arrays which are available in ComM, i.e. “n” ComMChannels were ComMGatewayType is set, result in “n” External Request Arrays in ComM |
| DCM_ActiveDiagnostic indication | The DCM module indicates an active diagnostic session. DCM need “full communication” = COMM_FULL_COMMUNICATION for diagnostic purpose |
| Active wake-up | Wake-up caused by the hosting ECU e.g. by a sensor. |
| Application signal scheduling | Sending of application signals according to the VMM. Scheduling of CAN application signals is performed by the Communication Module, scheduling of LIN application I-PDUs (a PDU containing signals) is performed by the LIN interface and scheduling of FlexRay application PDUs is performed by the FlexRay Interface module. |
| Bus sleep | No activity required on the communication bus (e.g. CAN bus sleep). |
| Bus communication messages | Bus communication messages are all messages that are sent on the communication bus. This can be either a diagnostic message or an application message. |
| COM Inhibition status | Defines whether full communication, silent communication or wakeup is allowed or not. |
| Communication Channel | The medium used to convey information from a sender (or transmitter) to a receiver. |
| Communication Mode | Mode determining which kind of communication are allowed: “full communication” = COMM_FULL_COMMUNICATION “no communication” = COMM_NO_COMMUNICATION “silent communication” = COMM_SILENT_COMMUNICATION Note: COMM_SILENT_COMMUNICATION can not be requested by a user. Internal mode for synchronizing network at shutdown |
| Diagnostic PDU scheduling | Sending of diagnostic PDUs. Scheduling of CAN diagnostic PDUs is performed by the diagnostic module, scheduling of LIN diagnostic PDUs is performed by the diagnostic module and the LIN interface and scheduling of FlexRay diagnostic PDUs is performed by the diagnostic module and the FlexRay Interface module. |
| ECU shut down | See ECU State Manager specification [6]. |
| Fan-out | Same message/indication are sent to multiple destinations/receivers |
| Independent software component | A separately developed software component performing a coherent set of functions with a minimum amount of interfaces to other software applications on an ECU. This can be e.g. a basic software component or an application software component. |
| Passive wake-up | Wake-up by another ECU and propagated (e.g. by bus or wake-upline) to the ECU currently in focus. |
| System User | An administration functionality (a specific "user", which is generated within the internal context of the ComM) for making a default request and for overriding the user requests. |
| User | Concept for requestors of the ECU State Manager module and of the Communication Manager Module. A user may be the BswM, a runnable entity, a SW-C or a group of SW-Cs, which act as a single unit towards the ECU State Manager module and the Communication Manager Module. |
| User Request | A User can request different Communication Modes from ComM |
| Managed channel | A ComM channel that is referenced exclusively from one other channel by ECUC parameter ComMManageReference (see ECUC_ComM_00893). |
| Managing channel | A ComM channel that references 1..n other channels by ECUC parameter ComMManageReference (see ECUC_ComM_00893). |
英日単語帳
日本語は仮訳
T.B.D.
参考(reference)
[1] List of Basic Software Modules
AUTOSAR_TR_BSWModuleList.pdf
[2] Layered Software Architecture
AUTOSAR_EXP_LayeredSoftwareArchitecture.pdf
[3] General Requirements on Basic Software Modules
AUTOSAR_SRS_BSWGeneral.pdf
[4] Requirements on Mode Management
AUTOSAR_SRS_ModeManagement.pdf
[5] Specification of ECU Configuration
AUTOSAR_TPS_ECUConfiguration.pdf
[6] Specification of ECU State Manager
AUTOSAR_SWS_ECUStateManager.pdf
[7] Specification of NVRAM Manager
AUTOSAR_SWS_NVRAMManager.pdf
[8] Specification of RTE Software
AUTOSAR_SWS_RTE.pdf
[9] Specification of Generic Network Management Interface
AUTOSAR_SWS_NetworkManagementInterface.pdf
[11] Specification of Diagnostic Communication Manager
AUTOSAR_SWS_DiagnosticCommunicationManager.pdf
[12] Specification of LIN Interface
AUTOSAR_SWS_LINInterface.pdf
[13] Specification of FlexRay Interface
AUTOSAR_SWS_FlexRayInterface.pdf
[14] Specification of Default Error Tracer
AUTOSAR_SWS_DefaultErrorTracer.pdf
[16] Specification of CAN Transceiver Driver
AUTOSAR_SWS_CANTransceiverDriver.pdf
[17] Specification of CAN Interface
AUTOSAR_SWS_CANInterface.pdf
[18] Specification of FlexRay Transceiver Driver
AUTOSAR_SWS_FlexRayTransceiver.pdf
[19] Specification of PDU Router
AUTOSAR_SWS_PDURouter.pdf
[20] Requirements on IPDU Multiplexer
AUTOSAR_SWS_IPDUM.pdf
[21] Specification of System Services Mode Management
AUTOSAR_SystemServices_ModeManagement.pdf
[22] Specification of C Implementation Rules
AUTOSAR_Tr_CImplementationRules.pdf
[23] Specification of LIN State Manager
AUTOSAR_SWS_LINStateManager.pdf
[24] Specification of CAN State Manager
AUTOSAR_SWS_CANStateManager.pdf
[25] Specification of FlexRay State Manager
AUTOSAR_SWS_FlexRayStateManager.pdf
[26] Basic Software Module Description Template,
AUTOSAR_TPS_BSWModuleDescriptionTemplate.pdf
[27] Glossary,
AUTOSAR_TR_Glossary.pdf
[28] Specification of Ethernet State Manager
AUTOSAR_SWS_EthernetStateManager.pdf
[29] Specification of Basic Software Mode Manager
AUTOSAR_SWS_BSWModeManager.pdf
[30] General Specification of Basic Software Modules
AUTOSAR_SWS_BSWGeneral.pdf
[31] Specification of System Template
AUTOSAR_TPS_SystemTemplate
[32] Specification of Guide to BSW Distribution
AUTOSAR_EXP_BSWDistributionGuide
[33] OPEN ALIANCE Sleep/Wake-up Specification Version 2.0 (Rel Feb 21, 2017),
http://www.opensig.org/Automotive-Ethernet-Specifications/