LoginSignup
0
0

Delete article

Deleted articles cannot be recovered.

Draft of this article would be also deleted.

Are you sure you want to delete this article?

More than 1 year has passed since last update.

@caa45040(caa45040)

ST7789V2を使いアナログ温度計で遊ぶ(STM32G031)(注意)

Last updated at Posted at 2023-12-04

x MCP9701-E/TO 販売コード 103199

ST7789V2を使いアナログ温度計で遊ぶ(STM32G031)(注意)

x 過去ログを見よ
x 4PINをOBでGPIO
x 6GPIO
x 書き換え時には、3秒以内にコネクトし、イレース
x LCDのりせっと回路が簡易なため不安定　電源を数回入れ直す

参考

目的
カラー液晶のテスト

o_cop838.jpg

o_cop837.jpg

i2c_run.h

i2c_run.h



//インクルド
#include <Wire.h>


//定義
//10の割り算 0から1028までは、正しい。主に0から999
#define DIV10(n) ((n*205)>>11)


void i2c_setup(){

//空関数

}//setup


void i2c_run(NA_ST7735_P *display_bk){

  NA_ST7735_P display = *display_bk;

  //アナログ値の読み込み  
  analogReadResolution(12); //adc 12bit mode
  int s = analogRead(A3);   // PA11 PIN5 031

  //電圧を温度に変換 ex 20.0 -> 200 温度の十倍を出力
  s = ((s * 1692) >> 12) - 205;

  // テキストサイズを設定
  display.setTextSize(3);
  // テキスト色を設定
  display.setTextColor(WHITE);
  // テキストの開始位置を設定
  display.setCursor(0, 0);
 
  // 1行目に46を表示
  display.println();
  display.println("-----------");
  display.println("temperature");
  display.println();
  display.print("  ");
  display.print( DIV10(s) );            // 小数点以上
  display.print(".");
  display.print( s - (DIV10(s) * 10) ); // 小数点以下
  display.print("C");
  display.println();
  display.println("-----------");

}//i2c_run

メインプログラム




//ili9341_SPI_monotone_REG7_031

//ヘッダーファイル
#include <Adafruit_GFX.h>
#include "hh.h"
#include "i2c_run.h"

//定義
#define SCREEN_WIDTH  (240-16-16) // OLED display width, in pixels
#define SCREEN_HEIGHT 200 // OLED display height, in pixels
NA_ST7735_P display(SCREEN_WIDTH, SCREEN_HEIGHT);


//初期化
void setup() {

  delay(3000); //do not delete

  // LCDの初期化
  display.begin();

  //i2cの初期化
  i2c_setup();

}//setup


//メインループ
void loop() {

  // 画面表示をクリア
  display.clearDisplay();

  i2c_run(&display);

  // 描画バッファの内容を画面に表示
  display.display();

  delay(500); //0.5秒待つ

}//loop

hh.cpp

hh.cpp


 
//インクルド
#include "hh.h"
#include <Adafruit_GFX.h>


//定義
#define NA_ST7735_P_swap(a, b)                                                     \
  (((a) ^= (b)), ((b) ^= (a)), ((a) ^= (b))) ///< No-temp-var swap operation
//GPIOの設定1　開始
#define DW    digitalWrite
//#define TFT_RST   A1
//#define TFT_RS    PA11
#define TFT_RS    PB7
#define TFT_CS    PA0
//#define TFT_CS    PA12
//#define GPIO_RESET(s)  DW(TFT_RST,s)
#define GPIO_RS(s)     DW(TFT_RS,s)
#define GPIO_CS(s)     DW(TFT_CS,s)

//#define TFT_MOSI PA12
//#define TFT_SCK  PB7

//honban
#define TFT_MOSI PA13
#define TFT_SCK  PA14

//debug
//#define TFT_MOSI PA12
//#define TFT_SCK  PA11

#define SPI_MOSI_HIGH() DW(TFT_MOSI,HIGH)
#define SPI_MOSI_LOW()  DW(TFT_MOSI,LOW)
#define SPI_SCK_HIGH()  DW(TFT_SCK,HIGH)
#define SPI_SCK_LOW()   DW(TFT_SCK,LOW)


void SPI_WRITE8(int x)
{
  for (int bit = 0; bit < 8; bit++) {
    if (x & 0x80) {
      SPI_MOSI_HIGH();
      SPI_SCK_HIGH();
      SPI_SCK_LOW();
    } else {
      SPI_MOSI_LOW();
      SPI_SCK_HIGH();
      SPI_SCK_LOW();
    }//end if
    x <<= 1;
  }//for
}//SPI_WRITE8

//c = CS,m=MOSI,C=SPICLK
//TFT_SPICLK  PA14
//TFT_MOSI    PA13
//TFT_CS      PA12(仮)
//TFT_CS      PA0(本番)
//                                          Cmc
//                                         5432109876543210
#define REG_MOSI_ON           GPIOA->ODR=0b0010000000000000;
//                                          Cmc
//                                         5432109876543210
#define REG_CLK_ON__MOSI_1    GPIOA->ODR=0b0110000000000000;
//                                          Cmc
//                                         5432109876543210
#define REG_MOSI_OFF          GPIOA->ODR=0b0000000000000000;
//                                          Cmc
//                                         5432109876543210
#define REG_CLK_ON__MOSI_0    GPIOA->ODR=0b0100000000000000;
//                                          Cmc
//                                         5432109876543210
#define REG_CLK_OFF           GPIOA->ODR=0b0000000000000000;


void SPI_WRITE8_A(int s)
{
  //1
  if (s & 0x80) {
    REG_MOSI_ON;
    REG_CLK_ON__MOSI_1;
    REG_CLK_OFF;
  } else {
    REG_MOSI_OFF;
    REG_CLK_ON__MOSI_0;
    REG_CLK_OFF;
  }//end if
  //2
  if (s & 0x40) {
    REG_MOSI_ON;
    REG_CLK_ON__MOSI_1;
    REG_CLK_OFF;
  } else {
    REG_MOSI_OFF;
    REG_CLK_ON__MOSI_0;
    REG_CLK_OFF;
  }//end if
  //3
  if (s & 0x20) {
    REG_MOSI_ON;
    REG_CLK_ON__MOSI_1;
    REG_CLK_OFF;
  } else {
    REG_MOSI_OFF;
    REG_CLK_ON__MOSI_0;
    REG_CLK_OFF;
  }//end if
  //4
  if (s & 0x10) {
    REG_MOSI_ON;
    REG_CLK_ON__MOSI_1;
    REG_CLK_OFF;
  } else {
    REG_MOSI_OFF;
    REG_CLK_ON__MOSI_0;
    REG_CLK_OFF;
  }//end if
  //5
  if (s & 0x08) {
    REG_MOSI_ON;
    REG_CLK_ON__MOSI_1;
    REG_CLK_OFF;
  } else {
    REG_MOSI_OFF;
    REG_CLK_ON__MOSI_0;
    REG_CLK_OFF;
  }//end if
  //6
  if (s & 0x04) {
    REG_MOSI_ON;
    REG_CLK_ON__MOSI_1;
    REG_CLK_OFF;
  } else {
    REG_MOSI_OFF;
    REG_CLK_ON__MOSI_0;
    REG_CLK_OFF;
  }//end if
  //7
  if (s & 0x02) {
    REG_MOSI_ON;
    REG_CLK_ON__MOSI_1;
    REG_CLK_OFF;
  } else {
    REG_MOSI_OFF;
    REG_CLK_ON__MOSI_0;
    REG_CLK_OFF;
  }//end if
  //8
  if (s & 0x01) {
    REG_MOSI_ON;
    REG_CLK_ON__MOSI_1;
    REG_CLK_OFF;
  } else {
    REG_MOSI_OFF;
    REG_CLK_ON__MOSI_0;
    REG_CLK_OFF;
  }//end if
}//SPI_WRITE8


void NA_ST7735_P::GPIO_8BIT(uint8_t s)
{
  SPI_WRITE8(s);
} //GPIO_8BIT


//コマンドの書き込み
void NA_ST7735_P::LCD_Write_CMD(uint8_t a)
{
  GPIO_CS(0);//CS=0; 12
  GPIO_RS(0); //A0=0; 9
  GPIO_8BIT(a);//P1=a; data SPI SPI
  GPIO_CS(1);//CS=1; 12
} //LCD_Write_CMD


//データ書き込み
void NA_ST7735_P::LCD_Write_Data(uint8_t a)
{
  GPIO_CS(0);//CS=0; 12
  GPIO_RS(1); //A0=1; 9
  GPIO_8BIT(a);//P1=a; data SPI SPI
  GPIO_CS(1);//CS=1; 12
} //LCD_Write_Data


//液晶の初期化処理
void NA_ST7735_P::TXDT144TF_ST7735S_Init(void)
{

  //GPIO_RESET(1);//LCD_RESET=1;
  //delay(1); //Delay 1ms

  //GPIO_RESET(0);//LCD_RESET=0;
  //delay(1); //Delay 1ms

  //GPIO_RESET(1);//LCD_RESET=1;
  //delay(120); //Delay 120ms

  LCD_Write_CMD(0x01);//SOFTWARE RESET
  delay(50);

  LCD_Write_CMD(0x01);//SOFTWARE RESET
  delay(50);

  LCD_Write_CMD(0x11);//SLEEP OUT
  delay(200);

  LCD_Write_CMD(0x29);//display on
  delay(100);

  LCD_Write_CMD(0x36);//RGB-RGR format
  LCD_Write_Data(0x00);//RGB mode
  delay(100);

  LCD_Write_CMD(0x3a);//Interface pixel format
  LCD_Write_Data(0x55);//16bit mode
  delay(100);

  LCD_Write_CMD(0x21); //Reverse
  delay(100);

} //TXDT144TF_ST7735S_Init


NA_ST7735_P::NA_ST7735_P(uint16_t w, uint16_t h)
  : Adafruit_GFX(w, h), buffer(NULL)

{
}


//バッファのクリア
NA_ST7735_P::~NA_ST7735_P(void) {
  if (buffer) {
    free(buffer);
    buffer = NULL;
  }
}//~NA_ST7735_P


//初期処理
bool NA_ST7735_P::begin(void) {

  if ((!buffer) && !(buffer = (uint8_t *)malloc( (((WIDTH)/8)*HEIGHT) ) )    )
    return false;

  //バッファーのクリア
  clearDisplay();

  //ポートのモード設定　アウトプットモード
  pinMode(TFT_CS, OUTPUT);
  //pinMode(TFT_RST, OUTPUT);
  pinMode(TFT_RS, OUTPUT);

  pinMode(TFT_MOSI, OUTPUT);
  pinMode(TFT_SCK , OUTPUT);


  //ポートの初期化
  GPIO_CS(1);//CS=1
  //GPIO_RESET(1);//RESET=1
  GPIO_RS(0);//RS=0


  delay(500); //0.5秒待つ

  //液晶の初期化処理
  TXDT144TF_ST7735S_Init();

  //画面の書き込み開始
  //display();

  return true; // Success
}//begin


//点の表示
void NA_ST7735_P::drawPixel(int16_t x, int16_t y, uint16_t color) {
  if ((x >= 0) && (x < width()) && (y >= 0) && (y < height())) {
    // Pixel is in-bounds. Rotate coordinates if needed.
    switch (getRotation()) {
      case 1:
        NA_ST7735_P_swap(x, y);
        x = WIDTH - x - 1;
        break;
      case 2:
        x = WIDTH - x - 1;
        y = HEIGHT - y - 1;
        break;
      case 3:
        NA_ST7735_P_swap(x, y);
        y = HEIGHT - y - 1;
        break;
    }
    switch (color) {
      case NA_ST7735_P_WHITE:
        //0      239
        //1      238
        //2      237
        //x = (WIDTH - 1) - x;
        buffer[(x / 8) +    (y * 26)  ] |=  (1 << (7 - (x & 7)));
        break;
      case NA_ST7735_P_BLACK:
        //x = (WIDTH - 1) - x;
        buffer[(x / 8) +    (y * 26)  ] &= ~(1 << (7 - (x & 7)));
        break;
      case NA_ST7735_P_INVERSE:
        //x = (WIDTH - 1) - x;
        buffer[(x / 8) +    (y * 26)  ] ^=  (1 << (7 - (x & 7)));
        break;
    }
  }
}


//バッファのクリア
void NA_ST7735_P::clearDisplay(void) {
  for(int ii=0;ii<( ((WIDTH)/8)*HEIGHT   );ii++){
    buffer[ii]=0;
  }//for
}


bool NA_ST7735_P::getPixel(int16_t x, int16_t y) {
  if ((x >= 0) && (x < width()) && (y >= 0) && (y < height())) {
    // Pixel is in-bounds. Rotate coordinates if needed.
    switch (getRotation()) {
      case 1:
        NA_ST7735_P_swap(x, y);
        x = WIDTH - x - 1;
        break;
      case 2:
        x = WIDTH - x - 1;
        y = HEIGHT - y - 1;
        break;
      case 3:
        NA_ST7735_P_swap(x, y);
        y = HEIGHT - y - 1;
        break;
    }
    //x = (WIDTH - 1) - x;
    return (buffer[(x / 8) +    (y * 26)  ] &  (1 << (7 - (x & 7))));
  }
  return false; // Pixel out of bounds
}


uint8_t *NA_ST7735_P::getBuffer(void) {
  return buffer;
}


//TFT_CS      PA12(仮)
//TFT_CS      PA0(本番)
//                                          Cm            c
//                                         5432109876543210
#define GPIO_CS_0()           GPIOA->ODR=0b0000000000000000;
//                                          Cm            c
//                                         5432109876543210
#define GPIO_CS_1()           GPIOA->ODR=0b0000000000000001;

//#define WR_D(xx)  GPIO_CS(0);SPI_WRITE8(xx);GPIO_CS(1);
#define WR_D(xx)  GPIO_CS_0();SPI_WRITE8_A(xx);GPIO_CS_1();


void g_line20() {
  //16dot
  for (int ooi = 0; ooi < 15; ooi++) {
    WR_D(0b00000110);
    WR_D(0b11100000);
  }//ooi
  WR_D(0b00000000);
  WR_D(0b0000000);
  for (int ppj = 0; ppj <  240 - 16 - 16; ppj++) {
    WR_D(0);
    WR_D(0);
  } //j
  //16dot
  WR_D(0b00000000);
  WR_D(0b00000000);
  for (int ooi = 0; ooi < 15; ooi++) {
    WR_D(0b00000110);
    WR_D(0b11100000);
  }//ooi
}//g_line20()


void NA_ST7735_P::display(void) {

  //画面の書き込み開始
  LCD_Write_CMD(0x2C); //memory write

  GPIO_RS(1); //A0=1; 9

  delay(4);

  int jjk = 0, vg = 0;
  int hp[8] = {0x80, 0x40, 0x20, 0x10,  0x08, 0x04, 0x02, 0x01};

  //20line
  for (int ooi = 0; ooi < (20); ooi++) {
    g_line20();
  }

  for (int i = 0; i < HEIGHT; i++) {

    //16dot
    for (int ooi = 0; ooi < 15; ooi++) {
      WR_D(0b00000110);
      WR_D(0b11100000);
    }//ooi
    WR_D(0b00000000);
    WR_D(0b0000000);

    //240-16-16
    for (int j = 0; j < ((WIDTH / 8)); j++) {
      //8dot
      vg = buffer[jjk];
      for (int k = 0; k < 8; k++) {
        if ( ( vg & hp[k]) == 0 ) {
          WR_D(0);
          WR_D(0);
        } else {
          WR_D(0xff);
          WR_D(0xff);
        }//end if
      }//k
      jjk++;
    } //j

    //16dot
    WR_D(0b00000000);
    WR_D(0b00000000);
    for (int ooi = 0; ooi < 15; ooi++) {
      WR_D(0b00000110);
      WR_D(0b11100000);
    }//ooi

  }//i

  //20line
  for (int ooi = 0; ooi < (20); ooi++) {
    g_line20();
  }//ooi

}//display

hh.h

hh.h



 
#ifndef _NA_ST7735_P_H_
#define _NA_ST7735_P_H_

#include <Adafruit_GFX.h>

#ifndef NO_ADAFRUIT_NA_ST7735_P_COLOR_COMPATIBILITY
#define BLACK NA_ST7735_P_BLACK     ///< Draw 'off' pixels
#define WHITE NA_ST7735_P_WHITE     ///< Draw 'on' pixels
#define INVERSE NA_ST7735_P_INVERSE ///< Invert pixels
#endif
/// fit into the SSD1306_ naming scheme
#define NA_ST7735_P_BLACK 0   ///< Draw 'off' pixels
#define NA_ST7735_P_WHITE 1   ///< Draw 'on' pixels
#define NA_ST7735_P_INVERSE 2 ///< Invert pixels


class NA_ST7735_P : public Adafruit_GFX {
  public:

    NA_ST7735_P(uint16_t w, uint16_t h);

    ~NA_ST7735_P(void);

    bool begin(void);
    void display(void);
    void clearDisplay(void);
    void drawPixel(int16_t x, int16_t y, uint16_t color);
    bool getPixel(int16_t x, int16_t y);
    uint8_t *getBuffer(void);

    void GPIO_8BIT(uint8_t s);
    void LCD_Write_CMD(uint8_t ww);
    void LCD_Write_Data(uint8_t ii);
    void TXDT144TF_ST7735S_Init(void);


  protected:


    uint8_t *buffer; ///< Buffer data used for display buffer. Allocated when
    ///< begin method is called.

};

#endif // _NA_ST7735_P_H_
0
0
0

Register as a new user and use Qiita more conveniently

  1. You get articles that match your needs
  2. You can efficiently read back useful information
  3. You can use dark theme
What you can do with signing up
Sign upLogin
0
0

Delete article

Deleted articles cannot be recovered.

Draft of this article would be also deleted.

Are you sure you want to delete this article?