Grbl_ESP32の設定
使うCNCボードの選択
Arduino > libraries > Grbl_Esp32 内の machine.hを設定
testから
#include "Machines/3axis_v4.h"
に変更
GRBL configrationの設定（デフォルト値）
Arduino > libraries > Grbl_Esp32 内の defaults.hを設定
NEJE Master2に合わせて設定を変更
ボード側のマイクロステップは16を選択
defaults.h
# ifndef defaults_h
/*
All of these settings check to see if they have been defined already
before defining them. This allows to to easily set them eslewhere.
You only need to set ones that are important or unique to your
machine. The rest will be pulled from here.
*/
// Grbl generic default settings. Should work across different machines.
#ifndef DEFAULT_STEP_PULSE_MICROSECONDS
#define DEFAULT_STEP_PULSE_MICROSECONDS 10 // $0
#endif
#ifndef DEFAULT_STEPPER_IDLE_LOCK_TIME
#define DEFAULT_STEPPER_IDLE_LOCK_TIME 25 // $1 msec (0-254, 255 keeps steppers enabled)
#endif
#ifndef DEFAULT_STEPPING_INVERT_MASK
#define DEFAULT_STEPPING_INVERT_MASK 0 // $2 uint8_t
#endif
#ifndef DEFAULT_DIRECTION_INVERT_MASK
#define DEFAULT_DIRECTION_INVERT_MASK 3 // $3 uint8_
#endif
#ifndef DEFAULT_INVERT_ST_ENABLE
#define DEFAULT_INVERT_ST_ENABLE 0 // $4 boolean
#endif
#ifndef DEFAULT_INVERT_LIMIT_PINS
#define DEFAULT_INVERT_LIMIT_PINS 1 // $5 boolean
#endif
#ifndef DEFAULT_INVERT_PROBE_PIN
#define DEFAULT_INVERT_PROBE_PIN 0 // $6 boolean
#endif
#ifndef DEFAULT_STATUS_REPORT_MASK
#define DEFAULT_STATUS_REPORT_MASK 1 // $10
#endif
#ifndef DEFAULT_JUNCTION_DEVIATION
#define DEFAULT_JUNCTION_DEVIATION 0.01 // $11 mm
#endif
#ifndef DEFAULT_ARC_TOLERANCE
#define DEFAULT_ARC_TOLERANCE 0.002 // $12 mm
#endif
#ifndef DEFAULT_REPORT_INCHES
#define DEFAULT_REPORT_INCHES 0 // $13 false
#endif
#ifndef DEFAULT_SOFT_LIMIT_ENABLE
#define DEFAULT_SOFT_LIMIT_ENABLE 1 // $20 True
#endif
#ifndef DEFAULT_HARD_LIMIT_ENABLE
#define DEFAULT_HARD_LIMIT_ENABLE 1 // $21 True
#endif
#ifndef DEFAULT_HOMING_ENABLE
#define DEFAULT_HOMING_ENABLE 1 // $22 enable
#endif
#ifndef DEFAULT_HOMING_DIR_MASK
#define DEFAULT_HOMING_DIR_MASK 3 // $23 move positive dir Z, negative X,Y
#endif
#ifndef DEFAULT_HOMING_FEED_RATE
#define DEFAULT_HOMING_FEED_RATE 25.0 // $24 mm/min
#endif
#ifndef DEFAULT_HOMING_SEEK_RATE
#define DEFAULT_HOMING_SEEK_RATE 500.0 // $25 mm/min
#endif
#ifndef DEFAULT_HOMING_DEBOUNCE_DELAY
#define DEFAULT_HOMING_DEBOUNCE_DELAY 800 // $26 msec (0-65k)
#endif
#ifndef DEFAULT_HOMING_PULLOFF
#define DEFAULT_HOMING_PULLOFF 1.0 // $27 mm
#endif
// ======== SPINDLE STUFF ====================
#ifndef SPINDLE_TYPE
#define SPINDLE_TYPE SPINDLE_TYPE_NONE
#endif
#ifndef DEFAULT_SPINDLE_RPM_MIN // $31
#define DEFAULT_SPINDLE_RPM_MIN 0.0 // rpm
#endif
#ifndef DEFAULT_LASER_MODE // $32
#define DEFAULT_LASER_MODE 1 // True
#endif
#ifndef DEFAULT_SPINDLE_RPM_MAX // $30
#define DEFAULT_SPINDLE_RPM_MAX 1000.0 // rpm
#endif
#ifndef DEFAULT_SPINDLE_FREQ
#define DEFAULT_SPINDLE_FREQ 5000.0 // $33 Hz (extended set)
#endif
#ifndef DEFAULT_SPINDLE_OFF_VALUE
#define DEFAULT_SPINDLE_OFF_VALUE 0.0 // $34 Percent of full period(extended set)
#endif
#ifndef DEFAULT_SPINDLE_MIN_VALUE
#define DEFAULT_SPINDLE_MIN_VALUE 0.0 // $35 Percent of full period (extended set)
#endif
#ifndef DEFAULT_SPINDLE_MAX_VALUE
#define DEFAULT_SPINDLE_MAX_VALUE 100.0 // $36 Percent of full period (extended set)
#endif
// ================ user settings =====================
#ifndef DEFAULT_USER_INT_80
#define DEFAULT_USER_INT_80 0 // $80 User integer setting
#endif
#ifndef DEFAULT_USER_INT_81
#define DEFAULT_USER_INT_81 0 // $81 User integer setting
#endif
#ifndef DEFAULT_USER_INT_82
#define DEFAULT_USER_INT_82 0 // $82 User integer setting
#endif
#ifndef DEFAULT_USER_INT_83
#define DEFAULT_USER_INT_83 0 // $83 User integer setting
#endif
#ifndef DEFAULT_USER_INT_84
#define DEFAULT_USER_INT_84 0 // $84 User integer setting
#endif
#ifndef DEFAULT_USER_FLOAT_90
#define DEFAULT_USER_FLOAT_90 0.0 // $90 User integer setting
#endif
#ifndef DEFAULT_USER_FLOAT_91
#define DEFAULT_USER_FLOAT_91 0.0 // $92 User integer setting
#endif
#ifndef DEFAULT_USER_FLOAT_92
#define DEFAULT_USER_FLOAT_92 0.0 // $92 User integer setting
#endif
#ifndef DEFAULT_USER_FLOAT_93
#define DEFAULT_USER_FLOAT_93 0.0 // $93 User integer setting
#endif
#ifndef DEFAULT_USER_FLOAT_94
#define DEFAULT_USER_FLOAT_94 0.0 // $94 User integer setting
#endif
// =========== AXIS RESOLUTION ======
#ifndef DEFAULT_X_STEPS_PER_MM
#define DEFAULT_X_STEPS_PER_MM 160.0
#endif
#ifndef DEFAULT_Y_STEPS_PER_MM
#define DEFAULT_Y_STEPS_PER_MM 160.0
#endif
#ifndef DEFAULT_Z_STEPS_PER_MM
#define DEFAULT_Z_STEPS_PER_MM 100.0
#endif
#ifndef DEFAULT_A_STEPS_PER_MM
#define DEFAULT_A_STEPS_PER_MM 100.0
#endif
#ifndef DEFAULT_B_STEPS_PER_MM
#define DEFAULT_B_STEPS_PER_MM 100.0
#endif
#ifndef DEFAULT_C_STEPS_PER_MM
#define DEFAULT_C_STEPS_PER_MM 100.0
#endif
// ============ AXIS MAX SPPED =========
#ifndef DEFAULT_X_MAX_RATE
#define DEFAULT_X_MAX_RATE 1000.0 // mm/min
#endif
#ifndef DEFAULT_Y_MAX_RATE
#define DEFAULT_Y_MAX_RATE 1000.0 // mm/min
#endif
#ifndef DEFAULT_Z_MAX_RATE
#define DEFAULT_Z_MAX_RATE 500.0 // mm/min
#endif
#ifndef DEFAULT_A_MAX_RATE
#define DEFAULT_A_MAX_RATE 1000.0 // mm/min
#endif
#ifndef DEFAULT_B_MAX_RATE
#define DEFAULT_B_MAX_RATE 1000.0 // mm/min
#endif
#ifndef DEFAULT_C_MAX_RATE
#define DEFAULT_C_MAX_RATE 1000.0 // mm/min
#endif
// ============== Axis Acceleration =========
#define SEC_PER_MIN_SQ (60.0*60.0) // Seconds Per Minute Squared, for acceleration conversion
// Default accelerations are expressed in mm/sec^2
#ifndef DEFAULT_X_ACCELERATION
#define DEFAULT_X_ACCELERATION 100.0
#endif
#ifndef DEFAULT_Y_ACCELERATION
#define DEFAULT_Y_ACCELERATION 100.0
#endif
#ifndef DEFAULT_Z_ACCELERATION
#define DEFAULT_Z_ACCELERATION 100.0
#endif
#ifndef DEFAULT_A_ACCELERATION
#define DEFAULT_A_ACCELERATION 200.0
#endif
#ifndef DEFAULT_B_ACCELERATION
#define DEFAULT_B_ACCELERATION 200.0
#endif
#ifndef DEFAULT_C_ACCELERATION
#define DEFAULT_C_ACCELERATION 200.0
#endif
// ========= AXIS MAX TRAVEL ============
#ifndef DEFAULT_X_MAX_TRAVEL
#define DEFAULT_X_MAX_TRAVEL 170.0 // $130 mm NOTE: Must be a positive value.
#endif
#ifndef DEFAULT_Y_MAX_TRAVEL
#define DEFAULT_Y_MAX_TRAVEL 170.0 // mm NOTE: Must be a positive value.
#endif
#ifndef DEFAULT_Z_MAX_TRAVEL
#define DEFAULT_Z_MAX_TRAVEL 50.0 // mm NOTE: Must be a positive value.
#endif
#ifndef DEFAULT_A_MAX_TRAVEL
#define DEFAULT_A_MAX_TRAVEL 300.0 // mm NOTE: Must be a positive value.
#endif
#ifndef DEFAULT_B_MAX_TRAVEL
#define DEFAULT_B_MAX_TRAVEL 300.0 // mm NOTE: Must be a positive value.
#endif
#ifndef DEFAULT_C_MAX_TRAVEL
#define DEFAULT_C_MAX_TRAVEL 300.0 // mm NOTE: Must be a positive value.
#endif
// ========== Motor current (SPI Drivers ) =============
#ifndef DEFAULT_X_CURRENT
#define DEFAULT_X_CURRENT 0.25 // $140 current in amps (extended set)
#endif
#ifndef DEFAULT_Y_CURRENT
#define DEFAULT_Y_CURRENT 0.25 // $141 current in amps (extended set)
#endif
#ifndef DEFAULT_Z_CURRENT
#define DEFAULT_Z_CURRENT 0.25 // $142 current in amps (extended set)
#endif
#ifndef DEFAULT_A_CURRENT
#define DEFAULT_A_CURRENT 0.25 // $143 current in amps (extended set)
#endif
#ifndef DEFAULT_B_CURRENT
#define DEFAULT_B_CURRENT 0.25 // $144 current in amps (extended set)
#endif
#ifndef DEFAULT_C_CURRENT
#define DEFAULT_C_CURRENT 0.25 // $145 current in amps (extended set)
#endif
// ========== Motor hold current (SPI Drivers ) =============
#ifndef DEFAULT_X_HOLD_CURRENT
#define DEFAULT_X_HOLD_CURRENT 0.125 // $150 current in amps (extended set)
#endif
#ifndef DEFAULT_Y_HOLD_CURRENT
#define DEFAULT_Y_HOLD_CURRENT 0.125 // $151 current in amps (extended set)
#endif
#ifndef DEFAULT_Z_HOLD_CURRENT
#define DEFAULT_Z_HOLD_CURRENT 0.125 // $152 current in amps (extended set)
#endif
#ifndef DEFAULT_A_HOLD_CURRENT
#define DEFAULT_A_HOLD_CURRENT 0.125 // $153 current in amps (extended set)
#endif
#ifndef DEFAULT_B_HOLD_CURRENT
#define DEFAULT_B_HOLD_CURRENT 0.125 // $154 current in amps (extended set)
#endif
#ifndef DEFAULT_C_HOLD_CURRENT
#define DEFAULT_C_HOLD_CURRENT 0.125 // $154 current in amps (extended set)
#endif
// ========== Microsteps (SPI Drivers ) ================
#ifndef DEFAULT_X_MICROSTEPS
#define DEFAULT_X_MICROSTEPS 16 // $160 micro steps (extended set)
#endif
#ifndef DEFAULT_Y_MICROSTEPS
#define DEFAULT_Y_MICROSTEPS 16 // $161 micro steps (extended set)
#endif
#ifndef DEFAULT_Z_MICROSTEPS
#define DEFAULT_Z_MICROSTEPS 16 // $162 micro steps (extended set)
#endif
#ifndef DEFAULT_A_MICROSTEPS
#define DEFAULT_A_MICROSTEPS 16 // $163 micro steps (extended set)
#endif
#ifndef DEFAULT_B_MICROSTEPS
#define DEFAULT_B_MICROSTEPS 16 // $164 micro steps (extended set)
#endif
#ifndef DEFAULT_C_MICROSTEPS
#define DEFAULT_C_MICROSTEPS 16 // $165 micro steps (extended set)
#endif
// ========== Stallguard (SPI Drivers ) ================
#ifndef DEFAULT_X_STALLGUARD
#define DEFAULT_X_STALLGUARD 16 // $170 stallguard (extended set)
#endif
#ifndef DEFAULT_Y_STALLGUARD
#define DEFAULT_Y_STALLGUARD 16 // $171 stallguard (extended set)
#endif
#ifndef DEFAULT_Z_STALLGUARD
#define DEFAULT_Z_STALLGUARD 16 // $172 stallguard (extended set)
#endif
#ifndef DEFAULT_A_STALLGUARD
#define DEFAULT_A_STALLGUARD 16 // $173 stallguard (extended set)
#endif
#ifndef DEFAULT_B_STALLGUARD
#define DEFAULT_B_STALLGUARD 16 // $174 stallguard (extended set)
#endif
#ifndef DEFAULT_C_STALLGUARD
#define DEFAULT_C_STALLGUARD 16 // $175 stallguard (extended set)
#endif
// ================== pin defaults ========================
// Here is a place to default pins to UNDEFINED_PIN.
// This can eliminate checking to see if the pin is defined because
// the overridden pinMode and digitalWrite functions will deal with it.
# ifndef STEPPERS_DISABLE_PIN
#define STEPPERS_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef X_DISABLE_PIN
#define X_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef Y_DISABLE_PIN
#define Y_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef Z_DISABLE_PIN
#define Z_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef A_DISABLE_PIN
#define A_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef B_DISABLE_PIN
#define B_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef C_DISABLE_PIN
#define C_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef X2_DISABLE_PIN
#define X2_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef Y2_DISABLE_PIN
#define Y2_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef Z2_DISABLE_PIN
#define Z2_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef A2_DISABLE_PIN
#define A2_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef B2_DISABLE_PIN
#define B2_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef C2_DISABLE_PIN
#define C2_DISABLE_PIN UNDEFINED_PIN
# endif
# ifndef X_LIMIT_PIN
#define X_LIMIT_PIN UNDEFINED_PIN
# endif
# ifndef Y_LIMIT_PIN
#define Y_LIMIT_PIN UNDEFINED_PIN
# endif
# ifndef Z_LIMIT_PIN
#define Z_LIMIT_PIN UNDEFINED_PIN
# endif
# ifndef A_LIMIT_PIN
#define A_LIMIT_PIN UNDEFINED_PIN
# endif
# ifndef B_LIMIT_PIN
#define B_LIMIT_PIN UNDEFINED_PIN
# endif
# ifndef C_LIMIT_PIN
#define C_LIMIT_PIN UNDEFINED_PIN
# endif
# endif
```
## スピンドル設定（レーザー）
3axis_v4.h 内の
#define SPINDLE_TYPE を SPINDLE_TYPE_LASER
に変更